Cisco Systems RVL200 manual Static IP, PPPoE Point-to-Point Protocol over Ethernet

Page 19

Chapter 4

Advanced Configuration

subscribers use this connection type.) Your ISP assigns these values.

Obtain an IP Automatically

DNS Server (Required) 1/2 If you select Use the Following DNS Server Addresses, enter your DNS server IP address(es) (enter at least one). Multiple DNS server IP settings are common. In most cases, the first available DNS entry is used.

MTU The MTU (Maximum Transmission Unit) setting specifies the largest packet size permitted for network transmission. To manually set a value, select Manual and enter the value desired in the field provided. You should leave this value in the 1200 to 1500 range, and most DSL users should use the value 1492. The default is Auto, which allows the Router to select the best MTU for your Internet connection.

Click Save Settings to save your changes, or click Cancel Changes to undo them.

Static IP

If you are required to use a permanent IP address, select Static IP.

Static IP

Specify WAN IP Address Enter the external IP address of the Router.

Subnet Mask Enter the subnet mask of the Router.

Default Gateway Address Enter the IP address of the default gateway.

DNS Server (Required) 1/2 If you select Use the Following DNS Server Addresses, enter your DNS server IP address(es) (enter at least one). Multiple DNS server IP settings are common. In most cases, the first available DNS entry is used.

MTU The MTU (Maximum Transmission Unit) setting specifies the largest packet size permitted for network transmission. To manually set a value, select Manual and enter the value desired in the field provided. You should leave this value in the 1200 to 1500 range, and most DSL users should use the value 1492. The default is Auto, which allows the Router to select the best MTU for your Internet connection.

Click Save Settings to save your changes, or click Cancel Changes to undo them.

PPPoE (Point-to-Point Protocol over Ethernet)

Some DSL-based Internet Service Providers (ISPs) use PPPoE (Point-to-Point Protocol over Ethernet) to establish Internet connections for end-users. If you use a DSL line, check with your ISP to see if they use PPPoE, select PPPoE.

PPPoE

User Name and Password Enter your account’s User Name and Password. The maximum number of characters is 60.

Connect on Demand If you select the Connect on Demand option, the connection will be disconnected after a specified period of inactivity (Max Idle Time). If you have been disconnected due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. Enter the number of minutes you want to have elapsed before your Internet access disconnects. The default Max Idle Time is 5 minutes.

4-Port SSL/IPSec VPN Router

11

Image 19

Contents Port SSL/IPSec VPN Router About This Guide About This GuideTable of Contents Ddns IPSec VPN Gateway to Gateway Appendix D Active Directory Server Appendix C Bandwidth ManagementAppendix E User for the Active Directory Server Appendix J IPSec NAT Traversal Appendix I Gateway-to-Gateway VPN TunnelAppendix L Multiple VLANs with Computers Appendix M Multiple VLANs and Subnets Appendix O Firmware UpgradeAppendix P Battery Replacement Appendix Q SpecificationsIntroduction to the Router ChapterChapter Introduction IntroductionComputer using SSL VPN client software to VPN Router Back Panel Chapter Product OverviewProduct Overview Front PanelInstallation Chapter InstallationPhysical Installation Cable Connection Before You Begin Chapter Advanced ConfigurationAdvanced Configuration OverviewClick Security Select Use SSL 2.0 and Use SSL How to Access the Web-Based UtilitySystem Information System SummarySSL VPN Setting Status Network Setting StatusFirewall Setting Status IPSec VPN Setting StatusWAN Connection Type Setup Tab NetworkLAN Setting NetworkPPPoE Point-to-Point Protocol over Ethernet Static IPPptp Point-to-Point Tunneling Protocol Setup PasswordTime Setup TimeSetup DMZ Host PasswordPort Triggering Setup Tab ForwardingForwarding Port Range ForwardingUPnP Setup UPnPSetup MAC Clone Setup One-to-One NATOne-to-One NAT Advanced Routing Setup DdnsSetup Advanced Routing MAC CloneStatic Routing Dhcp SetupDynamic IP SetupStatic IP Multiple VLANs Dhcp StatusStatus Dhcp Multiple VLANsInter-VLAN Routing System Management DiagnosticDiagnostic Dhcp Inter-VLAN RoutingFirmware Download Factory DefaultFirmware Upgrade System Management RestartRestart Import Configuration FileExport Configuration File System Management Port MirroringPort Status Port Management Port SetupBasic Per Port Config Port Management Port StatusCreate Vlan Port Management Port SettingPort Setting Port Management Create VlanVlan Membership QoS Bandwidth ManagementBandwidth Management Priority Rate ControlTrust Mode Default CoS QoS QoS SetupQoS Setup QoS ModeCoS Settings QoS Queue SettingsQoS Dscp Settings Queue SettingsDscp to Queue Dscp SettingsFirewall General GeneralAccess Rules Firewall Access RulesRestrict WEB Features Services Add a New Access RuleIP/MAC Group Firewall Content FilterContent Filter SchedulingIP Address IPSec VPN SummaryForbidden Domains Website Blocking by KeywordsAdd a New Tunnel Local Group SetupIPSec VPN Gateway to Gateway SummaryLocal Security Group Type Remote Group SetupRemote Security Gateway Type Remote Security Group Type IKE with Preshared Key IPSec SetupAdvanced VPN Pass Through IPSec VPN VPN Pass ThroughSSL VPN Summary SSL VPN Certificate ManagementEdit Group Authentication TypeSSL VPN User Management User ManagementEdit User SSL VPN Virtual PassageVirtual Passage Snmp Global ParametersGlobal Parameters Group Profile Snmp ViewsSnmp Group Profile ViewsCommunities Snmp Group MembershipSnmp Communities Group MembershipNotification Recipient Snmp Notification RecipientSystem Log Log System LogGeneral Log Log SettingLog System Statistics Alert LogWizard Basic SetupPPPoE Obtain an IP automaticallyAccess Rule Setup Select the Service Linksys Web Site SupportLogout ManualLogout Troubleshooting Appendix a TroubleshootingAppendix a Appendix B Virtual Passage SSL VPN Client Appendix BBefore You Begin Windows OS Click Trusted sites Make the SSL VPN Portal a Trusted Site Windows OSLogin for the SSL VPN Portal Windows OS Installation of the Virtual Passage Client Windows OSClick Continue Anyway When you right-click the icon, you have three optionsLogin for the SSL VPN Portal Mac OS Installation of the Virtual Passage Client Mac OSWindows Vista Usage Click Continue Removal of the Virtual Passage Client Mac OSLogin for the SSL VPN Portal Linux OS Installation of the Virtual Passage Client Linux OSBefore You Begin Linux OS Removal of the Virtual Passage Client Linux OS Bandwidth Management Creation of New ServicesAppendix C Appendix C Bandwidth ManagementCreation of New Bandwidth Management Rules Click Save SettingsAppendix D Active Directory Server Appendix DActive Directory Server Select Domain in a new forest, and then click Next Enter a domain name, and then click Next Active Directory Server Troubleshooting Appendix E User for the Active Directory Server Appendix EUser for the Active Directory Server Appendix F Appendix F Internet Authentication Service IAS ServerInternet Authentication Service IAS Server Select Unencrypted authentication. Click Apply Click Finish Welcome to the New Connection Request Policy Wizard Click Edit Profile Click the User Management tab Appendix GLAN-to-LAN Connection Select HTTPSTCP/443~443 from the Service drop- down menuAppendix H Appendix H Deployment in an Existing NetworkWAN-to-LAN Connection Click the Gateway to Gateway tab Configuration of the RVL200Appendix Appendix Gateway-to-Gateway VPN TunnelConfiguration of PC 1 and PC Configuration of the RV082RV082 RVL200 Dynamic IP B.B.B.B with Configuration when Both Gateways Use Dynamic IP Addresses Appendix Appendix J IPSec NAT Traversal Configuration of ScenarioConfiguration of Router a Appendix JIPSec NAT Traversal Configuration of Router BOne-to-One NAT Rule on NAT 1 RV042 One-to-One NAT Rule on NAT 2 RV042Configuration of Router a Appendix K Configuration of MultipleRVL200-to-RV042 Configuration Appendix KClick Save Setting RV042 #1 ConfigurationClick the Advanced Routing tab RV042 #2 Configuration Click the Port Management tab RVL200-to-SRW2048 ConfigurationAppendix L Appendix L Multiple VLANs with ComputersSelect Enable Vlan SRW2048 ConfigurationClick Save Settings Click the Vlan Membership tab Multiple VLANs RVL200 ConfigurationAppendix M Appendix MClick the Inter-VLAN Routing tab Inter-VLAN Routing OptionOver a SSL VPN Tunnel Access of Multiple VLANsAppendix N Appendix NFirmware Upgrade Appendix O Firmware UpgradeAppendix O Click the Firmware Upgrade tab Upgrade the FirmwareAppendix P Appendix P Battery ReplacementBattery Replacement Replace the Lithium BatterySpecifications Appendix Q SpecificationsAppendix Q Limited Warranty Warranty InformationAppendix R Regulatory Information Appendix SDansk Danish Miljøinformation for kunder i EU Port SSL/IPSec VPN Router 106 Norsk Norwegian Miljøinformasjon for kunder i EU Port SSL/IPSec VPN Router 108 Contact Information Appendix T