Cisco Systems RSP8 manual Delete the rsp-pv-mz.120-22.3.S1image from the standby RSP

Configuring High System Availability

Last, we delete the rsp-pv-mz.120-22.3.S1image from the standby RSP4/4+ card, as shown in Figure 11:

Figure 11 Software Error Protection—Backing Up with an Older Software Version, Part III

N￿￿￿AL N￿￿￿AL

ENABLE

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

A￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿

￿L￿￿￿￿￿￿		￿L￿￿￿￿￿L￿￿￿￿
￿L￿￿
￿A￿￿E￿		￿LA￿E￿A￿￿E￿
￿LA￿E
￿LA￿E￿￿A￿￿E￿		￿LA￿E￿￿A￿￿E￿
￿￿￿	￿￿AL￿	￿￿￿￿￿AL￿
￿E￿E￿		￿E￿E￿
A￿￿		A￿￿
￿￿N￿￿LE		￿￿N￿￿LE

ENABLE

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿

￿

￿

Complete the following steps to configure software error protection for this sample scenario:

Step 1 To verify the location and version of the RSP software images, use the following commands to view slot

0 on the active and standby RSPs:

Router# show slot0:
-#- ED ----		type----	--crc--- -	seek--	nlen	-length-	-----date/time------	name
1	.. image		143B4C13	ACB820	21	11188128	Jan 28 2000 01:02:37
rsp-pv-mz.120-22.3.S1
Router# show bootflash:
-#- ED ----		type----	--crc--- -	seek--	nlen	-length-	-----date/time------	name
1	.. image		143B4C13	ACB820	21	11188128	Jan 28 2000 01:02:37

rsp-pv-mz.120-22.3.S1

Step 2 Copy the Cisco IOS Release 12.0(23)S system image from a TFTP server to PC Card slot 0 on the active and standby RSPs:

Router# copy tftp slot0:rsp-pv-mz.120-23.S

Router# copy tftp slaveslotk0:rsp-pv-mz.120-23.S

Step 3 Delete the rsp-pv-mz.120-22.3.S1image from the standby RSP:

Router# delete slaveslot0:rsp-pv-mz.120-22.3.S1

Route Switch Processor (RSP8) Installation and Configuration Guide

OL-4920-02 37