Cisco Systems 1300 manual Conventions

Page 10

Preface

Conventions

Chapter 3, “Mounting Overview,” provides an overview of components and features used during access point/bridge mounting and antenna alignment operations.

Chapter 4, “Troubleshooting Autonomous Access Points and Bridges,” provides solutions to potential problems encountered during setup of autonomous access points.

Chapter 5, “Troubleshooting Lightweight Access Points,” provides solutions to potential problems encountered during setup of lightweightaccess points.

Appendix A, “Translated Safety Warnings,” indicates how to access the document that provides translations of the safety warnings that appear in this publication.

Appendix B, “Declarations of Conformity and Regulatory Information,” describes the regulatory conventions to which the access point/bridge conforms and provides guidelines for operating access point/bridges in Japan.

Appendix C, “Access Point Specifications,” describes the channels and antenna settings supported by the regulatory organizations.

Appendix D, “Channels and Maximum Power Levels,” indicates how to access the document that lists the access point/bridge radio channels and the maximum power levels supported by the world’s regulatory domains.

Appendix E, “Console Serial Cable Pinouts,” identifies the pinouts for the serial cable that connects to the power injector’s console serial port.

Appendix F, “Priming Lightweight Access Points Prior to Deployment,” describes the procedure to prime lightweight access points with controller information.

Appendix G, “Configuring DHCP Option 43 for Lightweight Access Points,” describes the procedure to configure DHCP Option 43 for lightweight access points.

Appendix H, “Load-Dump Protection for Transportation Vehicles,” describes load-dump protection that is required for autonomous access point/bridge operation in some transportation vehicles

Conventions

This publication uses the following conventions to convey instructions and information:

Commands and keywords are in boldface type.

Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual.

Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.

Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide

 

x

OL-5048-06

 

 

 

Image 10
Contents Corporate Headquarters Page N T E N T S IiiWindow Mounting Ssid Japanese Translation B-6 Load-Dump Protection H-1 ViiViii Purpose PrefaceAudience OrganizationConventions Preface Conventions Cisco.com Related PublicationsObtaining Documentation XiiProduct Documentation DVD Ordering Documentation Documentation FeedbackCisco Product Security Overview XiiiProduct Alerts and Field Notices Reporting Security Problems in Cisco ProductsXiv Obtaining Technical Assistance Cisco Support WebsiteLocating the Product Serial Number XviSubmitting a Service Request XviiObtaining Additional Publications and Information Definitions of Service Request SeverityXviii Xix OL-5048-06 Overview Autonomous Access Point/BridgeProduct Terminology Guidelines for Using a Lightweight Access Point/Bridge Lightweight Access PointKey Features Power 1shows the two outdoor access point/bridge configurationsIntegrated Antenna External AntennaEthernet Ports ConnectorsEnclosure LEDs Operating Roles for the Autonomous Access Point/Bridge Network Examples with Autonomous Access Point/Bridges Repeater Unit that Extends Wireless RangeRoot Access Point on a Wired LAN Access Points as Root Units on a Wired LANCentral Unit in an All-Wireless Network Bridge Network with Wireless ClientsPoint-to-Point Bridge Configuration Workgroup Bridge NetworkNetwork Examples with Lightweight Access Points OL-5048-06 Installation Overview Safety Warnings All InstallationsDC Power Source Installations Safety InformationOutdoor and DC Power Source Installations FCC Safety Compliance StatementInstallation Overview Safety Information Installation Guidelines Typical Outdoor Installation ComponentsPackage Contents Unpacking the Access Point/BridgeSite Surveys Before Beginning the Installation Access Point/Bridge Layout Installation Summary Installation Overview Installation Summary Mounting the Access Point/Bridge, Mounting Hardware, LEDs, Mounting OverviewMounting the Access Point/Bridge Mounting HardwareWindow Mounting Multi-Function MountAccess Point Bracket LEDs Install LED Status Rssi Level dBm Ethernet LED Status LED Radio LED OL-5048-06 Troubleshooting Autonomous Access Points and Bridges Checking the LEDs on an Autonomous Access Point/Bridge Ethernet Status Radio Install Meaning Blinking Codes First Second Power Injector Default IP Address Behavior Checking PowerChecking Basic Configuration Settings Default Ssid and Radio BehaviorEnabling the Radio Interface SsidAntenna Alignment Security SettingsRunning the Carrier Busy Test Running the Ping or Link Test Using the Web-Browser Interface Using the CLI on an Autonomous Access Point/Bridge Reloading the Access Point/Bridge ImageWeb-Browser Interface Browser Http Interface Obtaining the Autonomous Access Point/Bridge Image File Connecting to the Console Serial Port Console Serial Port ConnectorObtaining the Tftp Server Software Http//tftpd32.jounin.netOL-5048-06 Troubleshooting Lightweight Access Points Checking the LEDs on Lightweight Access Points LED Indications Troubleshooting Lightweight Access Points Power Injector Using Dhcp Option Console serial port connector RJ-45 connector Configuring Controller Information Clearing Manually Entered Controller InformationReturning the Access Point to Autonomous Mode Manually Resetting the Access Point to DefaultsObtaining the Autonomous Access Point Image File OL-5048-06 Translated Safety Warnings OL-5048-06 Declarations of Conformity and Regulatory Information For Home or Office USE Vcci Statement for Japan Industry Canada Canadian Compliance StatementOL-5048-06 EMC Declaration of Conformity for RF Exposure Japanese TranslationAll Access Points and Bridges English TranslationEnglish Translation Operation of Cisco Aironet Access Points in Brazil Access Point ModelsDeclaration of Conformity Statements Page OL-5048-06 Access Point Specifications Category Access Point Power Injector and Power ModuleOfdm Category Access Point Power Injector and Power Module Category Access Point Power Injector and Power Module Channels and Maximum Power Levels OL-5048-06 Overview, page E-2 Signals and Pinouts, page E-2 Console Serial Cable PinoutsSignals and Pinouts OverviewPriming Lightweight Access Points Prior to Deployment OL-5048-06 Page OL-5048-06 Access Points Access Point Vendor Class Identifier VCI Quotation marks must be included Type + Length + Value Load-Dump Protection for Transportation Vehicles Load-Dump ProtectionAppendix H Load-Dump Protection for Transportation Vehicles Numeric GL-1Signal continuously over a wide frequency band GL-2GL-3 Single data message packet sent to multiple addresses GL-4Power level of radio transmission GL-5GL-6 D E IN-1Site survey Size C-1 SSID, troubleshooting IN-2
Related manuals
Manual 6 pages 38.55 Kb