Cisco Systems 1300 manual Installation Overview Installation Summary

Page 44

Chapter 2 Installation Overview

Installation Summary

For outdoor installations, connect the dual-coax Ethernet cables between the power injector and the grounding block. For indoor installations, connect the dual-coax cables to the power injector.

Tip You can connect the dual-coax cable connectors to either of the grounding block connectors or the power injector’s dual-coax Ethernet ports. The access point/bridge senses the Ethernet signals and automatically switches internal circuitry to match the cable connections.

Note You should securely tighten the cable connectors (15 to 20 inch-pounds) using a small wrench.

For outdoor installations, connect a ground wire to the grounding block.

Mount the access point/bridge to the mast, tower, or wall. For additional information, refer to the mounting instructions that shipped with your access point/bridge.

Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Connect a ground wire to the access point/bridge (use the ground lug).

For outdoor installations, connect the dual-coax Ethernet cables to the grounding block and to the access point/bridge. For indoor installations, connect the dual-coax cables directly to the access point/bridge.

Tip You can connect the dual-coax cable connectors to either of the grounding block connectors or the access point/bridge’s dual-coax ports. The access point/bridge senses the Ethernet signals and automatically switches internal circuitry to match the cable connections.

Note You should securely tighten the cable connectors (15 to 20 inch-pounds) using a small wrench.

Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A Statement 1005

For indoor installations, connect these items:

The AC power cord to the 48-VDC power module.

The power module power plug to the power injector and plug the AC cord into an AC power receptacle.

For outdoor installations, refer to the mounting instruction document that shipped with your access point/bridge.

Seal all external connectors with special weather sealing material.

Configure security and other access point/bridge options. For additional information, refer to the Cisco IOS Software Configuration Guide for Access Points or the Cisco Wireless LAN Controller Configuration Guide.

Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide

2-10

OL-5048-06

 

 

Image 44
Contents Corporate Headquarters Page N T E N T S IiiWindow Mounting Ssid Japanese Translation B-6 Load-Dump Protection H-1 ViiViii Preface AudiencePurpose OrganizationConventions Preface Conventions Related Publications Obtaining DocumentationCisco.com XiiDocumentation Feedback Cisco Product Security OverviewProduct Documentation DVD Ordering Documentation XiiiXiv Reporting Security Problems in Cisco ProductsProduct Alerts and Field Notices Obtaining Technical Assistance Cisco Support WebsiteLocating the Product Serial Number XviSubmitting a Service Request XviiXviii Definitions of Service Request SeverityObtaining Additional Publications and Information Xix OL-5048-06 Product Terminology Autonomous Access Point/BridgeOverview Guidelines for Using a Lightweight Access Point/Bridge Lightweight Access PointKey Features Power 1shows the two outdoor access point/bridge configurationsIntegrated Antenna External AntennaEnclosure ConnectorsEthernet Ports LEDs Operating Roles for the Autonomous Access Point/Bridge Network Examples with Autonomous Access Point/Bridges Repeater Unit that Extends Wireless RangeRoot Access Point on a Wired LAN Access Points as Root Units on a Wired LANCentral Unit in an All-Wireless Network Bridge Network with Wireless ClientsPoint-to-Point Bridge Configuration Workgroup Bridge NetworkNetwork Examples with Lightweight Access Points OL-5048-06 Installation Overview Safety Warnings All InstallationsSafety Information Outdoor and DC Power Source InstallationsDC Power Source Installations FCC Safety Compliance StatementInstallation Overview Safety Information Installation Guidelines Typical Outdoor Installation ComponentsSite Surveys Unpacking the Access Point/BridgePackage Contents Before Beginning the Installation Access Point/Bridge Layout Installation Summary Installation Overview Installation Summary Mounting the Access Point/Bridge, Mounting Hardware, LEDs, Mounting OverviewMounting the Access Point/Bridge Mounting HardwareWindow Mounting Multi-Function MountAccess Point Bracket LEDs Install LED Status Rssi Level dBm Ethernet LED Status LED Radio LED OL-5048-06 Troubleshooting Autonomous Access Points and Bridges Checking the LEDs on an Autonomous Access Point/Bridge Ethernet Status Radio Install Meaning Blinking Codes First Second Power Injector Checking Power Checking Basic Configuration SettingsDefault IP Address Behavior Default Ssid and Radio BehaviorEnabling the Radio Interface SsidRunning the Carrier Busy Test Security SettingsAntenna Alignment Running the Ping or Link Test Using the Web-Browser Interface Web-Browser Interface Reloading the Access Point/Bridge ImageUsing the CLI on an Autonomous Access Point/Bridge Browser Http Interface Obtaining the Autonomous Access Point/Bridge Image File Connecting to the Console Serial Port Console Serial Port ConnectorObtaining the Tftp Server Software Http//tftpd32.jounin.netOL-5048-06 Troubleshooting Lightweight Access Points Checking the LEDs on Lightweight Access Points LED Indications Troubleshooting Lightweight Access Points Power Injector Using Dhcp Option Console serial port connector RJ-45 connector Configuring Controller Information Clearing Manually Entered Controller InformationReturning the Access Point to Autonomous Mode Manually Resetting the Access Point to DefaultsObtaining the Autonomous Access Point Image File OL-5048-06 Translated Safety Warnings OL-5048-06 Declarations of Conformity and Regulatory Information For Home or Office USE Vcci Statement for Japan Industry Canada Canadian Compliance StatementOL-5048-06 EMC Declaration of Conformity for RF Exposure Japanese TranslationAll Access Points and Bridges English TranslationEnglish Translation Operation of Cisco Aironet Access Points in Brazil Access Point ModelsDeclaration of Conformity Statements Page OL-5048-06 Access Point Specifications Category Access Point Power Injector and Power ModuleOfdm Category Access Point Power Injector and Power Module Category Access Point Power Injector and Power Module Channels and Maximum Power Levels OL-5048-06 Overview, page E-2 Signals and Pinouts, page E-2 Console Serial Cable PinoutsSignals and Pinouts OverviewPriming Lightweight Access Points Prior to Deployment OL-5048-06 Page OL-5048-06 Access Points Access Point Vendor Class Identifier VCI Quotation marks must be included Type + Length + Value Load-Dump Protection for Transportation Vehicles Load-Dump ProtectionAppendix H Load-Dump Protection for Transportation Vehicles Numeric GL-1Signal continuously over a wide frequency band GL-2GL-3 Single data message packet sent to multiple addresses GL-4Power level of radio transmission GL-5GL-6 D E IN-1Site survey Size C-1 SSID, troubleshooting IN-2
Related manuals
Manual 6 pages 38.55 Kb

1300 specifications

Cisco Systems 1300 series, commonly referred to as the Cisco Aironet 1300 Series, represents a pivotal advancement in wireless networking solutions designed for outdoor environments. These access points are primarily intended for outdoor wireless applications, including temporary installations, public areas, and enterprises requiring robust outdoor coverage.

One of the standout features of the Cisco 1300 series is its ruggedized design. The access points are built to withstand harsh weather conditions, including extreme temperatures and precipitation. They comply with IP67 ratings, ensuring protection against dust and water intrusion, making them suitable for deployment in various environmental conditions.

The Cisco 1300 series provides comprehensive WLAN coverage through its support for various wireless standards, including 802.11b, 802.11g, and 802.11n. This compatibility ensures interoperability with existing wireless infrastructure while enabling faster data rates and improved connectivity. The technology leveraged in the Cisco 1300 series offers enhanced throughput and capacity, ensuring seamless connectivity for end-users.

Another key characteristic is the integration of advanced security features. The access points support robust encryption protocols, such as WPA2 and 802.1X, safeguarding sensitive data transmitted over the air. The ability to create secure guest access networks also enhances security, allowing organizations to provide internet access without compromising internal network safety.

Cisco's proprietary features, such as Cisco CleanAir technology, further enhance the performance of the 1300 series. This technology effectively detects and mitigates wireless interference, ensuring optimal performance and reliability in congested areas. Additionally, the series supports mesh networking capabilities, allowing for flexible deployment without the necessity of extensive wiring, which is particularly advantageous for temporary or mobile installations.

Management and configuration are simplified through the use of Cisco's Wireless LAN Controller (WLC). This centralized management allows network administrators to streamline firmware upgrades, monitor performance, and enforce policy compliance across multiple access points.

In summary, the Cisco Systems 1300 series access points combine robust outdoor capabilities with advanced wireless technology, security features, and ease of management, making them a valuable asset for organizations looking to extend their networking capabilities into outdoor environments. Through their durable design and innovative technologies, the Cisco 1300 series meets the demanding needs of today’s wireless landscape.