Cisco Systems 1300 manual Emc

Page 85

Appendix B Declarations of Conformity and Regulatory Information

European Community, Switzerland, Norway, Iceland, and Liechtenstein

This device complies with the EMC requirements (EN 60601-1-2) of the Medical Directive 93/42/EEC.

This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

For the 1300 series access point/bridge, the following standards were applied:

•	Radio:	EN 300.328-1, EN 300.328-2
•	EMC:	EN 301 489-1, EN 301 489-17
•	Safety:	EN 60950

The following CE mark is affixed to the 1300 series equipment:

The above CE mark is required as of April 8, 2000 but might change in the future.

Note This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance.

Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide

	OL-5048-06	B-5

Image 85

Contents Corporate Headquarters Page Iii N T E N T SWindow Mounting Ssid Japanese Translation B-6 Vii Load-Dump Protection H-1Viii Audience PrefacePurpose OrganizationConventions Preface Conventions Obtaining Documentation Related PublicationsCisco.com XiiCisco Product Security Overview Documentation FeedbackProduct Documentation DVD Ordering Documentation XiiiProduct Alerts and Field Notices Reporting Security Problems in Cisco ProductsXiv Cisco Support Website Obtaining Technical AssistanceXvi Locating the Product Serial NumberXvii Submitting a Service RequestObtaining Additional Publications and Information Definitions of Service Request SeverityXviii Xix OL-5048-06 Overview Autonomous Access Point/BridgeProduct Terminology Lightweight Access Point Guidelines for Using a Lightweight Access Point/BridgeKey Features 1shows the two outdoor access point/bridge configurations PowerExternal Antenna Integrated AntennaEthernet Ports ConnectorsEnclosure LEDs Operating Roles for the Autonomous Access Point/Bridge Repeater Unit that Extends Wireless Range Network Examples with Autonomous Access Point/BridgesAccess Points as Root Units on a Wired LAN Root Access Point on a Wired LANBridge Network with Wireless Clients Central Unit in an All-Wireless NetworkWorkgroup Bridge Network Point-to-Point Bridge ConfigurationNetwork Examples with Lightweight Access Points OL-5048-06 Installation Overview All Installations Safety WarningsOutdoor and DC Power Source Installations Safety InformationDC Power Source Installations FCC Safety Compliance StatementInstallation Overview Safety Information Typical Outdoor Installation Components Installation GuidelinesPackage Contents Unpacking the Access Point/BridgeSite Surveys Before Beginning the Installation Access Point/Bridge Layout Installation Summary Installation Overview Installation Summary Mounting Overview Mounting the Access Point/Bridge, Mounting Hardware, LEDs,Mounting Hardware Mounting the Access Point/BridgeMulti-Function Mount Window MountingAccess Point Bracket LEDs Install LED Status Rssi Level dBm Ethernet LED Status LED Radio LED OL-5048-06 Troubleshooting Autonomous Access Points and Bridges Checking the LEDs on an Autonomous Access Point/Bridge Ethernet Status Radio Install Meaning Blinking Codes First Second Power Injector Checking Basic Configuration Settings Checking PowerDefault IP Address Behavior Default Ssid and Radio BehaviorSsid Enabling the Radio InterfaceAntenna Alignment Security SettingsRunning the Carrier Busy Test Running the Ping or Link Test Using the Web-Browser Interface Using the CLI on an Autonomous Access Point/Bridge Reloading the Access Point/Bridge ImageWeb-Browser Interface Browser Http Interface Obtaining the Autonomous Access Point/Bridge Image File Console Serial Port Connector Connecting to the Console Serial PortHttp//tftpd32.jounin.net Obtaining the Tftp Server SoftwareOL-5048-06 Troubleshooting Lightweight Access Points Checking the LEDs on Lightweight Access Points LED Indications Troubleshooting Lightweight Access Points Power Injector Using Dhcp Option Console serial port connector RJ-45 connector Clearing Manually Entered Controller Information Configuring Controller InformationManually Resetting the Access Point to Defaults Returning the Access Point to Autonomous ModeObtaining the Autonomous Access Point Image File OL-5048-06 Translated Safety Warnings OL-5048-06 Declarations of Conformity and Regulatory Information For Home or Office USE Canadian Compliance Statement Vcci Statement for Japan Industry CanadaOL-5048-06 EMC Japanese Translation Declaration of Conformity for RF ExposureEnglish Translation All Access Points and BridgesEnglish Translation Access Point Models Operation of Cisco Aironet Access Points in BrazilDeclaration of Conformity Statements Page OL-5048-06 Category Access Point Power Injector and Power Module Access Point SpecificationsOfdm Category Access Point Power Injector and Power Module Category Access Point Power Injector and Power Module Channels and Maximum Power Levels OL-5048-06 Console Serial Cable Pinouts Overview, page E-2 Signals and Pinouts, page E-2Overview Signals and PinoutsPriming Lightweight Access Points Prior to Deployment OL-5048-06 Page OL-5048-06 Access Points Access Point Vendor Class Identifier VCI Quotation marks must be included Type + Length + Value Load-Dump Protection Load-Dump Protection for Transportation VehiclesAppendix H Load-Dump Protection for Transportation Vehicles GL-1 NumericGL-2 Signal continuously over a wide frequency bandGL-3 GL-4 Single data message packet sent to multiple addressesGL-5 Power level of radio transmissionGL-6 IN-1 D EIN-2 Site survey Size C-1 SSID, troubleshooting

Related manuals

Manual 6 pages 38.55 Kb