Cisco Systems 1300 manual Integrated Antenna, External Antenna

Page 25

Chapter 1 Overview

Key Features

•Cisco Aironet Power Injector LR2T—optional transportation version

–12- to 40-VDC input power

Note The power injector and the power module must not be placed in an outdoor unprotected environment. The power module must not be placed in a building’s environmental air space, such as above a suspended ceiling.

Integrated Antenna

The access point/bridge is available with an integrated 13-dBi patch array antenna. The antenna is covered with a radome to protect it from environmental elements. The integrated antenna is vertically polarized.

Note Some international regulatory regions may restrict the integrated antenna access point/bridge configuration.

External Antenna

The access point/bridge is available in an external antenna configuration (see Figure 1-1) for use with Cisco Aironet 2.4-GHz antennas. Two reverse-TNC type RF connectors are provided on the end of the unit to support single or diversity antenna configurations. The antennas connect to the access point/bridge antenna connectors using a coax cable. Table 1-1lists the external antennas supported by the access point/bridge.

Table 1-1	Supported External Antennas

Antenna		Description

AIR-ANT2506		5.2-dBi omnidirectional antenna with vertical polarization

AIR-ANT3549		9-dBi patch wall mount antenna

AIR-ANT2410Y-R		10-dBi yagi antenna

AIR-ANT241201		12-dBi omnidirectional antenna with vertical polarization
AIR-ANT19491		13.5-dBi yagi antenna
AIR-ANT2414S-R1		14-dBi sector antenna with vertical polarization
AIR-ANT33381		21-dBi dish antenna

1. Not supported by the lightweight access point (AIR-LAP1310G)

Note To meet regulatory restrictions, the external antenna access point/bridge unit and the external antenna must be professionally installed. The network administrator or other IT professional responsible for installing and configuring the unit is a suitable professional installer. Following installation, access to the unit should be password protected by the network administrator to maintain regulatory compliance.

Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide

	OL-5048-06	1-5

Image 25

Contents Corporate Headquarters Page Iii N T E N T SWindow Mounting Ssid Japanese Translation B-6 Vii Load-Dump Protection H-1Viii Audience PrefacePurpose OrganizationConventions Preface Conventions Obtaining Documentation Related PublicationsCisco.com XiiCisco Product Security Overview Documentation FeedbackProduct Documentation DVD Ordering Documentation XiiiProduct Alerts and Field Notices Reporting Security Problems in Cisco ProductsXiv Cisco Support Website Obtaining Technical AssistanceXvi Locating the Product Serial NumberXvii Submitting a Service RequestObtaining Additional Publications and Information Definitions of Service Request SeverityXviii Xix OL-5048-06 Overview Autonomous Access Point/BridgeProduct Terminology Lightweight Access Point Guidelines for Using a Lightweight Access Point/BridgeKey Features 1shows the two outdoor access point/bridge configurations PowerExternal Antenna Integrated AntennaEthernet Ports ConnectorsEnclosure LEDs Operating Roles for the Autonomous Access Point/Bridge Repeater Unit that Extends Wireless Range Network Examples with Autonomous Access Point/BridgesAccess Points as Root Units on a Wired LAN Root Access Point on a Wired LANBridge Network with Wireless Clients Central Unit in an All-Wireless NetworkWorkgroup Bridge Network Point-to-Point Bridge ConfigurationNetwork Examples with Lightweight Access Points OL-5048-06 Installation Overview All Installations Safety WarningsOutdoor and DC Power Source Installations Safety InformationDC Power Source Installations FCC Safety Compliance StatementInstallation Overview Safety Information Typical Outdoor Installation Components Installation GuidelinesPackage Contents Unpacking the Access Point/BridgeSite Surveys Before Beginning the Installation Access Point/Bridge Layout Installation Summary Installation Overview Installation Summary Mounting Overview Mounting the Access Point/Bridge, Mounting Hardware, LEDs,Mounting Hardware Mounting the Access Point/BridgeMulti-Function Mount Window MountingAccess Point Bracket LEDs Install LED Status Rssi Level dBm Ethernet LED Status LED Radio LED OL-5048-06 Troubleshooting Autonomous Access Points and Bridges Checking the LEDs on an Autonomous Access Point/Bridge Ethernet Status Radio Install Meaning Blinking Codes First Second Power Injector Checking Basic Configuration Settings Checking PowerDefault IP Address Behavior Default Ssid and Radio BehaviorSsid Enabling the Radio InterfaceAntenna Alignment Security SettingsRunning the Carrier Busy Test Running the Ping or Link Test Using the Web-Browser Interface Using the CLI on an Autonomous Access Point/Bridge Reloading the Access Point/Bridge ImageWeb-Browser Interface Browser Http Interface Obtaining the Autonomous Access Point/Bridge Image File Console Serial Port Connector Connecting to the Console Serial PortHttp//tftpd32.jounin.net Obtaining the Tftp Server SoftwareOL-5048-06 Troubleshooting Lightweight Access Points Checking the LEDs on Lightweight Access Points LED Indications Troubleshooting Lightweight Access Points Power Injector Using Dhcp Option Console serial port connector RJ-45 connector Clearing Manually Entered Controller Information Configuring Controller InformationManually Resetting the Access Point to Defaults Returning the Access Point to Autonomous ModeObtaining the Autonomous Access Point Image File OL-5048-06 Translated Safety Warnings OL-5048-06 Declarations of Conformity and Regulatory Information For Home or Office USE Canadian Compliance Statement Vcci Statement for Japan Industry CanadaOL-5048-06 EMC Japanese Translation Declaration of Conformity for RF ExposureEnglish Translation All Access Points and BridgesEnglish Translation Access Point Models Operation of Cisco Aironet Access Points in BrazilDeclaration of Conformity Statements Page OL-5048-06 Category Access Point Power Injector and Power Module Access Point SpecificationsOfdm Category Access Point Power Injector and Power Module Category Access Point Power Injector and Power Module Channels and Maximum Power Levels OL-5048-06 Console Serial Cable Pinouts Overview, page E-2 Signals and Pinouts, page E-2Overview Signals and PinoutsPriming Lightweight Access Points Prior to Deployment OL-5048-06 Page OL-5048-06 Access Points Access Point Vendor Class Identifier VCI Quotation marks must be included Type + Length + Value Load-Dump Protection Load-Dump Protection for Transportation VehiclesAppendix H Load-Dump Protection for Transportation Vehicles GL-1 NumericGL-2 Signal continuously over a wide frequency bandGL-3 GL-4 Single data message packet sent to multiple addressesGL-5 Power level of radio transmissionGL-6 IN-1 D EIN-2 Site survey Size C-1 SSID, troubleshooting

Related manuals

Manual 6 pages 38.55 Kb