Cisco Systems 12000 series specifications Ejector Levers

Page 15

Removing and Installing a Line Card

Note In Cisco 12008 and Cisco 12012 Routers, the 4-port ATM ISE line card uses a pair of line card slots. You must install the blank filler into the rightmost slot of the pair before you can install the 4-port ATM ISE line card.

Caution The router may indicate a hardware failure if you do not follow proper procedures. Remove or insert only one line card at a time. Allow at least 15 seconds for the router to complete the preceding tasks before removing or inserting another line card.

To install a line card, follow these steps:

Step 1 Attach an ESD-preventive wrist or ankle strap and follow its instructions for use.

Step 2 Choose an available line card slot for the line card, and verify that the line card interface cable is long enough for you to connect the line card with any external equipment.

Note If you are installing a 4-port ATM ISE line card into a Cisco 12008 or Cisco 12012 Router, you must install the line card into the slot to the left of the blank filler.

Caution To prevent ESD damage, handle line cards by the captive installation screws, the provided handle, ejector levers, or the card carrier edges only. Do not touch any of the electrical components or circuitry.

Step 3 Grasp the faceplate (or handle) of the line card with one hand and place your other hand under the card carrier to support the weight of the card; position the card for insertion into the card cage slot. Avoid touching the line card printed circuit board, components, or any connector pins.

Step 4 Carefully slide the line card into the slot until the ejector levers make contact with the edges of the card cage, then stop when the ejector lever hooks catch the lip of the card cage. If they do not catch, try reinserting the line card until the ejector lever hooks are fully latched. (See Figure 9.)

Figure 9

Ejector Levers

When inserting a card, make sure the ejector lever hooks catch the lip of the card cage.

H7681

ATM Line Card Installation and Configuration

 

OL-13004-01

15

 

 

 

Image 15
Contents ATM Line Card Installation and Configuration ContentsImportant Information Supported Platforms Router Hardware InstallationATM Line Card Product Numbers Cisco IOS Software Release RequirementsHardware Revision Requirements Compatible Cisco IOS ReleaseHardware Revision Number Product Overviews Related DocumentationPort OC-12c/STM-4c ATM Line Card Overview Port OC-3c/STM-1 ATM Line Card Overview 101926 Safety Guidelines Preparing for InstallationRemoving and Installing a Line Card Preventing Electrostatic DischargeRequired Tools and Equipment Guidelines for Line Card Removal and Installation Removing a Line Card Line Card Removal and Installation Removing the Blank Filler Installing a Blank FillerInserting and Removing the Blank Filler Fastening Captive Screw on Blank Filler Installing a Line CardEjector Levers Removing and Installing a Line Card Line Card Cable-Management Bracket Line Card Cable-Management BracketMultiport Line Card Cable-Management Bracket Removing a Line Card Cable-Management Bracket 80220 Installing a Line Card Cable-Management Bracket Cabling and Specifications ATM Line Card Power Budget and Signal SpecificationsPort OC-12c/STM-4c ATM Line Card Power Specifications Transceiver DBm Distance Port OC-3c/STM-1 ATM Line Card Power SpecificationsAttenuation Typical MaximumPort OC-12c/STM-4c ISE ATM Line Card Power Specifications Port OC-3c/STM-1 ISE ATM Line Card Power SpecificationsFiber-Optic Network Interface Cables RX port TX port Duplex or simplex SC fiber cable connectors Initial Boot Process Verifying and Troubleshooting Line Card InstallationStatus LEDs Alphanumeric LEDsState Description Nnnn LED Display Meaning SourceVget IOS Done Fabl Troubleshooting the Installation Parameter Configuration File Entry Default Value Configuring and Troubleshooting InterfacesInitial Configuration Configuring an InterfaceRouter# show version Using show Commands to Check Status Using the show version CommandUsing the show gsr Command Using ATM show Commands ATM Configuration ExampleUsing the show interfaces Command Using the show running-config CommandOutput Examples Advanced Line Card TroubleshootingShow context summary Output Show context slot Output Checking the Current Status of the Line CardFabric Ping Failure Error MessagesFpga Error Messages Configuring and Troubleshooting Interfaces Configuring and Troubleshooting Interfaces Line Card Memory Locations Line Card MemoryEngine 0 and Engine 1 Line Card Memory Locations Engine 0 and Engine 1 Line Card Memory LocationsISE Line Card Memory Locations Engine 2 Line Card Memory LocationsLine Card Memory UpgradeLC-Slot3#show hardware ATM Line Card Route Memory OptionsRemoving and Installing Line Card Memory ATM Line Card Packet Memory OptionsCisco Product Number Dimm Modules Dimm Sockets Dimm Socket with Dual Release Levers Removing a DimmDimm Socket with Single Release Lever Installing a DimmHandling a Dimm Removing a SodimmRemove Retaining Clip from Memory Module Socket Using the Dimm Removal Tools to Release the Sodimm Removing a 144-pin Sodimm Module Sodimm Socket Retaining Clip Installing a SodimmSodimm with Key in Face-Up Position Inserting the Retaining Clip Retaining Clip Installed into Module Latch Checking the Installation of Line Card MemoryFCC Class a Compliance Regulatory, Compliance, and Safety InformationTranslated Safety Warnings and Agency Approvals Electromagnetic Compatibility Regulatory StatementsCanada Europe-EUVcci Class a Notice for Japan Regulatory, Compliance, and Safety Information Obtaining Documentation
Related manuals
Manual 263 pages 10.29 Kb