Cisco Systems 12000 series specifications Regulatory, Compliance, and Safety Information

Page 61

Regulatory, Compliance, and Safety Information

Class A Notice for Hungary

Warning This equipment is a class A product and should be used and installed properly according to the Hungarian EMC Class A requirements (MSZEN55022). Class A equipment is designed for typical commercial establishments for which special conditions of installation and protection distance are used. Statement 256

Class A Notice for Taiwan and Other Traditional Chinese Markets

Warning This is a Class A Information Product, when used in residential environment, it may cause radio frequency interference, under such circumstances, the user may be requested to take appropriate countermeasures. Statement 257

Class A Notice for Korea

Warning This is a Class A Device and is registered for EMC requirements for industrial use. The seller or buyer should be aware of this. If this type was sold or purchased by mistake, it should be replaced with a residential-use type. Statement 294

ATM Line Card Installation and Configuration

 

OL-13004-01

61

 

 

 

Image 61
Contents Contents ATM Line Card Installation and ConfigurationImportant Information ATM Line Card Product Numbers Router Hardware InstallationCisco IOS Software Release Requirements Supported PlatformsCompatible Cisco IOS Release Hardware Revision RequirementsHardware Revision Number Related Documentation Product OverviewsPort OC-12c/STM-4c ATM Line Card Overview Port OC-3c/STM-1 ATM Line Card Overview 101926 Safety Guidelines Preparing for InstallationPreventing Electrostatic Discharge Removing and Installing a Line CardRequired Tools and Equipment Guidelines for Line Card Removal and Installation Removing a Line Card Line Card Removal and Installation Removing the Blank Filler Installing a Blank FillerInserting and Removing the Blank Filler Fastening Captive Screw on Blank Filler Installing a Line CardEjector Levers Removing and Installing a Line Card Line Card Cable-Management Bracket Line Card Cable-Management BracketMultiport Line Card Cable-Management Bracket Removing a Line Card Cable-Management Bracket 80220 Installing a Line Card Cable-Management Bracket ATM Line Card Power Budget and Signal Specifications Cabling and SpecificationsPort OC-12c/STM-4c ATM Line Card Power Specifications Attenuation Port OC-3c/STM-1 ATM Line Card Power SpecificationsTypical Maximum Transceiver DBm DistancePort OC-3c/STM-1 ISE ATM Line Card Power Specifications Port OC-12c/STM-4c ISE ATM Line Card Power SpecificationsFiber-Optic Network Interface Cables RX port TX port Duplex or simplex SC fiber cable connectors Initial Boot Process Verifying and Troubleshooting Line Card InstallationAlphanumeric LEDs Status LEDsState Description Nnnn LED Display Meaning SourceVget IOS Done Fabl Troubleshooting the Installation Initial Configuration Configuring and Troubleshooting InterfacesConfiguring an Interface Parameter Configuration File Entry Default ValueRouter# show version Using the show version Command Using show Commands to Check StatusUsing the show gsr Command Using the show interfaces Command ATM Configuration ExampleUsing the show running-config Command Using ATM show CommandsOutput Examples Advanced Line Card TroubleshootingShow context summary Output Show context slot Output Checking the Current Status of the Line CardFabric Ping Failure Error MessagesFpga Error Messages Configuring and Troubleshooting Interfaces Configuring and Troubleshooting Interfaces Line Card Memory Locations Line Card MemoryEngine 0 and Engine 1 Line Card Memory Locations Engine 0 and Engine 1 Line Card Memory LocationsISE Line Card Memory Locations Engine 2 Line Card Memory LocationsLine Card Memory UpgradeLC-Slot3#show hardware ATM Line Card Route Memory OptionsATM Line Card Packet Memory Options Removing and Installing Line Card MemoryCisco Product Number Dimm Modules Dimm Sockets Dimm Socket with Dual Release Levers Removing a DimmDimm Socket with Single Release Lever Installing a DimmHandling a Dimm Removing a SodimmRemove Retaining Clip from Memory Module Socket Using the Dimm Removal Tools to Release the Sodimm Removing a 144-pin Sodimm Module Sodimm Socket Retaining Clip Installing a SodimmSodimm with Key in Face-Up Position Inserting the Retaining Clip Retaining Clip Installed into Module Latch Checking the Installation of Line Card MemoryTranslated Safety Warnings and Agency Approvals Regulatory, Compliance, and Safety InformationElectromagnetic Compatibility Regulatory Statements FCC Class a ComplianceEurope-EU CanadaVcci Class a Notice for Japan Regulatory, Compliance, and Safety Information Obtaining Documentation
Related manuals
Manual 263 pages 10.29 Kb