Cisco Systems 12000 series specifications Product Overviews, Related Documentation

Page 4

Product Overviews

Related Documentation

This publication describes the basic installation and configuration of a ATM line card. For complete software and ATM configuration information, refer to the following publications:

Cisco 12000 Series Router Installation and Configuration Guides

Cisco 12000 Series Internet Router Configuration Guide for Cisco IOS Release 12.0S

Cisco IOS Configuration Fundamentals Configuration Guide

Cisco IOS Configuration Fundamentals Command Reference

Cisco IOS Release 12.0S Release Notes for Cisco 12000 Series Routers

4-Port ATM ISE Line Card Feature Module

Regulatory Compliance and Safety Information for Cisco 12000 Series Internet Routers

See the “Obtaining Documentation” section on page 62 for information on how to obtain these publications.

Product Overviews

This section includes product overview information for each ATM line card:

1-portOC-12c/STM-4c ATM Line Card Overview, page 4

4-portOC-3c/STM-1 ATM Line Card Overview, page 5

4-portOC-12c/STM-4c ATM Line Card Overview, page 5

8-portOC-3c/STM-1 ATM Line Card Overview, page 6

4-portOC-12c/STM-4c ISE and 4-portOC-3c/STM-1 ISE ATM Line Card Overview, page 6

1-port OC-12c/STM-4c ATM Line Card Overview

The 1-port OC-12c/STM-4c ATM line card provides the Cisco 12000 series router with one 622-Mbps ATM interface. The card interfaces to the router’s switch fabric and provides one OC-12c/STM-4c duplex SC single-mode or multimode SONET/SDH connection. This connection is concatenated, which provides for increased efficiency by eliminating the need to partition the bandwidth.

Figure 1 illustrates the single-mode, intermediate-range 1-port OC-12c/STM-4c ATM line card.

Figure 1

1-port OC-12c/STM-4c ATM Line Card—Single-Mode

ACTIVECARRIERRXCELL

0

1

2

3

OC-12/STM-4 SM IR ATM

4

101924

 

 

1

Ejector lever

3

Status LEDs

 

 

 

 

 

 

 

2

Port 0

4

Display LEDs

 

 

 

 

 

 

 

 

 

 

 

 

 

ATM Line Card Installation and Configuration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

OL-13004-01

 

 

 

 

 

 

 

 

Image 4
Contents Contents ATM Line Card Installation and ConfigurationImportant Information Router Hardware Installation ATM Line Card Product NumbersCisco IOS Software Release Requirements Supported PlatformsCompatible Cisco IOS Release Hardware Revision RequirementsHardware Revision Number Related Documentation Product OverviewsPort OC-12c/STM-4c ATM Line Card Overview Port OC-3c/STM-1 ATM Line Card Overview 101926 Preparing for Installation Safety GuidelinesPreventing Electrostatic Discharge Removing and Installing a Line CardRequired Tools and Equipment Guidelines for Line Card Removal and Installation Removing a Line Card Line Card Removal and Installation Installing a Blank Filler Removing the Blank FillerInserting and Removing the Blank Filler Installing a Line Card Fastening Captive Screw on Blank FillerEjector Levers Removing and Installing a Line Card Line Card Cable-Management Bracket Line Card Cable-Management BracketMultiport Line Card Cable-Management Bracket Removing a Line Card Cable-Management Bracket 80220 Installing a Line Card Cable-Management Bracket ATM Line Card Power Budget and Signal Specifications Cabling and SpecificationsPort OC-12c/STM-4c ATM Line Card Power Specifications Port OC-3c/STM-1 ATM Line Card Power Specifications AttenuationTypical Maximum Transceiver DBm DistancePort OC-3c/STM-1 ISE ATM Line Card Power Specifications Port OC-12c/STM-4c ISE ATM Line Card Power SpecificationsFiber-Optic Network Interface Cables RX port TX port Duplex or simplex SC fiber cable connectors Verifying and Troubleshooting Line Card Installation Initial Boot ProcessAlphanumeric LEDs Status LEDsState Description LED Display Meaning Source NnnnVget IOS Done Fabl Troubleshooting the Installation Configuring and Troubleshooting Interfaces Initial ConfigurationConfiguring an Interface Parameter Configuration File Entry Default ValueRouter# show version Using the show version Command Using show Commands to Check StatusUsing the show gsr Command ATM Configuration Example Using the show interfaces CommandUsing the show running-config Command Using ATM show CommandsAdvanced Line Card Troubleshooting Output ExamplesShow context summary Output Checking the Current Status of the Line Card Show context slot OutputError Messages Fabric Ping FailureFpga Error Messages Configuring and Troubleshooting Interfaces Configuring and Troubleshooting Interfaces Line Card Memory Line Card Memory LocationsEngine 0 and Engine 1 Line Card Memory Locations Engine 0 and Engine 1 Line Card Memory LocationsEngine 2 Line Card Memory Locations ISE Line Card Memory LocationsMemory Upgrade Line CardATM Line Card Route Memory Options LC-Slot3#show hardwareATM Line Card Packet Memory Options Removing and Installing Line Card MemoryCisco Product Number Dimm Modules Dimm Sockets Removing a Dimm Dimm Socket with Dual Release LeversInstalling a Dimm Dimm Socket with Single Release LeverRemoving a Sodimm Handling a DimmRemove Retaining Clip from Memory Module Socket Using the Dimm Removal Tools to Release the Sodimm Removing a 144-pin Sodimm Module Installing a Sodimm Sodimm Socket Retaining ClipSodimm with Key in Face-Up Position Inserting the Retaining Clip Checking the Installation of Line Card Memory Retaining Clip Installed into Module LatchRegulatory, Compliance, and Safety Information Translated Safety Warnings and Agency ApprovalsElectromagnetic Compatibility Regulatory Statements FCC Class a ComplianceEurope-EU CanadaVcci Class a Notice for Japan Regulatory, Compliance, and Safety Information Obtaining Documentation
Related manuals
Manual 263 pages 10.29 Kb