Cisco Systems 12000 series specifications Engine 0 and Engine 1 Line Card Memory Locations

Page 44

Line Card Memory

Engine 0 and Engine 1 Line Card Memory Locations

Figure 18 shows the dual in-line memory module (DIMM) socket locations on an Engine 0 or Engine 1 line card. This line card is equipped with six DIMM sockets:

Two route memory DIMM sockets

Two pairs of packet memory DIMM sockets (RX and TX pairs)

Figure 18 Engine 0 and Engine 1 Line Card Memory Locations

1

2

3

4

93275

0

ACTIVECARRIERPKT

 

RX

1

ACTIVECARRIERPKT

 

RX

Q OC- 3/STM-POS

5

6

1

Route memory DIMM0

4

Packet memory RX DIMM1

 

 

 

 

2

Route memory DIMM1

5

Packet memory TX DIMM0

 

 

 

 

3

Packet memory RX DIMM0

6

Packet memory TX DIMM1

 

 

 

 

ATM Line Card Installation and Configuration

44

OL-13004-01

 

 

Image 44
Contents Important Information ATM Line Card Installation and ConfigurationContents Router Hardware Installation ATM Line Card Product NumbersCisco IOS Software Release Requirements Supported PlatformsHardware Revision Number Hardware Revision RequirementsCompatible Cisco IOS Release Port OC-12c/STM-4c ATM Line Card Overview Product OverviewsRelated Documentation Port OC-3c/STM-1 ATM Line Card Overview 101926 Preparing for Installation Safety GuidelinesRequired Tools and Equipment Removing and Installing a Line CardPreventing Electrostatic Discharge Guidelines for Line Card Removal and Installation Removing a Line Card Line Card Removal and Installation Installing a Blank Filler Removing the Blank FillerInserting and Removing the Blank Filler Installing a Line Card Fastening Captive Screw on Blank FillerEjector Levers Removing and Installing a Line Card Line Card Cable-Management Bracket Line Card Cable-Management BracketMultiport Line Card Cable-Management Bracket Removing a Line Card Cable-Management Bracket 80220 Installing a Line Card Cable-Management Bracket Port OC-12c/STM-4c ATM Line Card Power Specifications Cabling and SpecificationsATM Line Card Power Budget and Signal Specifications Port OC-3c/STM-1 ATM Line Card Power Specifications AttenuationTypical Maximum Transceiver DBm DistanceFiber-Optic Network Interface Cables Port OC-12c/STM-4c ISE ATM Line Card Power SpecificationsPort OC-3c/STM-1 ISE ATM Line Card Power Specifications RX port TX port Duplex or simplex SC fiber cable connectors Verifying and Troubleshooting Line Card Installation Initial Boot ProcessState Description Status LEDsAlphanumeric LEDs LED Display Meaning Source NnnnVget IOS Done Fabl Troubleshooting the Installation Configuring and Troubleshooting Interfaces Initial ConfigurationConfiguring an Interface Parameter Configuration File Entry Default ValueRouter# show version Using the show gsr Command Using show Commands to Check StatusUsing the show version Command ATM Configuration Example Using the show interfaces CommandUsing the show running-config Command Using ATM show CommandsAdvanced Line Card Troubleshooting Output ExamplesShow context summary Output Checking the Current Status of the Line Card Show context slot OutputError Messages Fabric Ping FailureFpga Error Messages Configuring and Troubleshooting Interfaces Configuring and Troubleshooting Interfaces Line Card Memory Line Card Memory LocationsEngine 0 and Engine 1 Line Card Memory Locations Engine 0 and Engine 1 Line Card Memory LocationsEngine 2 Line Card Memory Locations ISE Line Card Memory LocationsMemory Upgrade Line CardATM Line Card Route Memory Options LC-Slot3#show hardwareCisco Product Number Dimm Modules Dimm Sockets Removing and Installing Line Card MemoryATM Line Card Packet Memory Options Removing a Dimm Dimm Socket with Dual Release LeversInstalling a Dimm Dimm Socket with Single Release LeverRemoving a Sodimm Handling a DimmRemove Retaining Clip from Memory Module Socket Using the Dimm Removal Tools to Release the Sodimm Removing a 144-pin Sodimm Module Installing a Sodimm Sodimm Socket Retaining ClipSodimm with Key in Face-Up Position Inserting the Retaining Clip Checking the Installation of Line Card Memory Retaining Clip Installed into Module LatchRegulatory, Compliance, and Safety Information Translated Safety Warnings and Agency ApprovalsElectromagnetic Compatibility Regulatory Statements FCC Class a ComplianceVcci Class a Notice for Japan CanadaEurope-EU Regulatory, Compliance, and Safety Information Obtaining Documentation
Related manuals
Manual 263 pages 10.29 Kb