Cisco Systems 12000 series specifications Fiber-Optic Network Interface Cables

Page 24

Cabling and Specifications

Table 7

8-port OC-3c/STM-1 ATM Line Card Power Specifications

 

 

 

 

 

 

 

 

 

 

 

 

 

Typical Maximum

Transceiver

 

Attenuation

Transmit Power

Receive Power

Distance

 

 

 

 

 

Single-mode, intermediate-reach (IR), 1310 nm

13 dB

–15 to –8 dBm

–20 to –8 dBm

13 miles (21 km)

 

 

 

 

 

Multimode, short-reach (SR), 1310 nm

10 dB

–20 to –14 dBm

–30 to –14 dBm

1.2 miles (2 km)

 

 

 

 

 

 

4-port OC-12c/STM-4c ISE ATM Line Card Power Specifications

The 4-port OC-12c/STM-4c ISE ATM line card provides the Cisco 12000 Series Router with four

622-Mbps ATM interfaces. Table 8 lists the power ratings and distances of these interfaces. The actual distance in any given case depends on the quality of the fiber attached to the transceiver.

Table 8

4-port OC-12c/STM-4c ISE ATM Line Card Power Specifications

 

 

 

 

 

 

 

 

 

 

 

 

 

Typical Maximum

Transceiver

 

Attenuation

Transmit Power

Receive Power

Distance

 

 

 

 

 

Single-mode, intermediate-reach (IR), 1310 nm

13 dB

–15 to –8 dBm

–28 to –8 dBm

9.3 miles (15 km)

 

 

 

 

 

Multimode, short-reach (SR), 1310 nm

6 dB

–20 to –14 dBm

–26 to –14 dBm

1.2 miles (2 km)

 

 

 

 

 

 

4-port OC-3c/STM-1 ISE ATM Line Card Power Specifications

The 4-port OC-3c/STM-1 ISE ATM line card provides the Cisco 12000 Series Router with four

155-Mbps ATM interfaces. Table 9 lists the power ratings and distances of these interfaces. The actual distance in any given case depends on the quality of the fiber attached to the transceiver.

Table 9

4-port OC-3c/STM-1 ATM Line Card Power Specifications

 

 

 

 

 

 

 

 

 

 

 

 

 

Typical Maximum

Transceiver

 

Attenuation

Transmit Power

Receive Power

Distance

 

 

 

 

 

Single-mode, intermediate-reach (IR), 1310 nm

13 dB

–15 to –8 dBm

–28 to –8 dBm

9.3 miles (15 km)

 

 

 

 

 

Multimode, short-reach (SR), 1310 nm

10 dB

–20 to –14 dBm

–30 to –14 dBm

1.2 miles (2 km)

 

 

 

 

 

 

Fiber-Optic Network Interface Cables

The ATM line cards have SC-type fiber-optic interface connectors. Use a multimode or single-mode fiber-optic interface cable, as appropriate, to connect the fiber-optic interfaces in the ATM line card in your Cisco 12000 series router to another router or switch. In general, multimode cables are gray or orange, and single-mode cables are yellow.

Note Single-mode and multimode fiber-optic cables are available from cable vendors. These cables are not available from Cisco Systems. The plug on the cable may be supplied with a dust cover. If it is, remove it before trying to connect it to the line card port.

You can use either one duplex SC-type connector (Figure 15) or two simplex SC-type connectors (Figure 16).

ATM Line Card Installation and Configuration

24

OL-13004-01

 

 

Image 24
Contents ATM Line Card Installation and Configuration ContentsImportant Information Router Hardware Installation ATM Line Card Product NumbersCisco IOS Software Release Requirements Supported PlatformsHardware Revision Requirements Compatible Cisco IOS ReleaseHardware Revision Number Product Overviews Related DocumentationPort OC-12c/STM-4c ATM Line Card Overview Port OC-3c/STM-1 ATM Line Card Overview 101926 Preparing for Installation Safety GuidelinesRemoving and Installing a Line Card Preventing Electrostatic DischargeRequired Tools and Equipment Guidelines for Line Card Removal and Installation Removing a Line Card Line Card Removal and Installation Installing a Blank Filler Removing the Blank FillerInserting and Removing the Blank Filler Installing a Line Card Fastening Captive Screw on Blank FillerEjector Levers Removing and Installing a Line Card Line Card Cable-Management Bracket Line Card Cable-Management BracketMultiport Line Card Cable-Management Bracket Removing a Line Card Cable-Management Bracket 80220 Installing a Line Card Cable-Management Bracket Cabling and Specifications ATM Line Card Power Budget and Signal SpecificationsPort OC-12c/STM-4c ATM Line Card Power Specifications Port OC-3c/STM-1 ATM Line Card Power Specifications AttenuationTypical Maximum Transceiver DBm DistancePort OC-12c/STM-4c ISE ATM Line Card Power Specifications Port OC-3c/STM-1 ISE ATM Line Card Power SpecificationsFiber-Optic Network Interface Cables RX port TX port Duplex or simplex SC fiber cable connectors Verifying and Troubleshooting Line Card Installation Initial Boot ProcessStatus LEDs Alphanumeric LEDsState Description LED Display Meaning Source NnnnVget IOS Done Fabl Troubleshooting the Installation Configuring and Troubleshooting Interfaces Initial ConfigurationConfiguring an Interface Parameter Configuration File Entry Default ValueRouter# show version Using show Commands to Check Status Using the show version CommandUsing the show gsr Command ATM Configuration Example Using the show interfaces CommandUsing the show running-config Command Using ATM show CommandsAdvanced Line Card Troubleshooting Output ExamplesShow context summary Output Checking the Current Status of the Line Card Show context slot OutputError Messages Fabric Ping FailureFpga Error Messages Configuring and Troubleshooting Interfaces Configuring and Troubleshooting Interfaces Line Card Memory Line Card Memory LocationsEngine 0 and Engine 1 Line Card Memory Locations Engine 0 and Engine 1 Line Card Memory LocationsEngine 2 Line Card Memory Locations ISE Line Card Memory LocationsMemory Upgrade Line CardATM Line Card Route Memory Options LC-Slot3#show hardwareRemoving and Installing Line Card Memory ATM Line Card Packet Memory OptionsCisco Product Number Dimm Modules Dimm Sockets Removing a Dimm Dimm Socket with Dual Release LeversInstalling a Dimm Dimm Socket with Single Release LeverRemoving a Sodimm Handling a DimmRemove Retaining Clip from Memory Module Socket Using the Dimm Removal Tools to Release the Sodimm Removing a 144-pin Sodimm Module Installing a Sodimm Sodimm Socket Retaining ClipSodimm with Key in Face-Up Position Inserting the Retaining Clip Checking the Installation of Line Card Memory Retaining Clip Installed into Module LatchRegulatory, Compliance, and Safety Information Translated Safety Warnings and Agency ApprovalsElectromagnetic Compatibility Regulatory Statements FCC Class a ComplianceCanada Europe-EUVcci Class a Notice for Japan Regulatory, Compliance, and Safety Information Obtaining Documentation
Related manuals
Manual 263 pages 10.29 Kb