Cisco Systems 12000 series Engine 2 Line Card Memory Locations, ISE Line Card Memory Locations

Page 45

Line Card Memory

Engine 2 Line Card Memory Locations

Figure 19 shows the DIMM socket locations on an Engine 2 line card. This line card is equipped with eight DIMM sockets:

Two route memory DIMM sockets

Two pairs of packet memory DIMM sockets (RX and TX pairs)

One pointer look-up (PLU) memory DIMM socket (not user serviceable)

One table look-up (TLU) memory DIMM socket (not user serviceable)

Figure 19 Engine 2 Line Card Memory Locations

1

2

3

4

TX

RX

AC

E

ARRIER PKT

TIV

 

0

C

RX

5

OC-

7

8

48/POS-SR-

SC

 

 

93276

6

1

Route memory DIMM0

5

Packet memory RX DIMM0

 

 

 

 

2

Route memory DIMM1

6

Packet memory RX DIMM1

 

 

 

 

3

Packet memory TX DIMM0

7

PLU DIMM (not user serviceable)

 

 

 

 

4

Packet memory TX DIMM1

8

TLU DIMM (not user serviceable)

 

 

 

 

ISE Line Card Memory Locations

Figure 20 shows the small outline memory DIMM (SODIMM) socket locations for route memory on an ATM ISE line card.

ATM Line Card Installation and Configuration

 

OL-13004-01

45

 

 

 

Image 45
Contents ATM Line Card Installation and Configuration ContentsImportant Information ATM Line Card Product Numbers Router Hardware InstallationCisco IOS Software Release Requirements Supported PlatformsHardware Revision Requirements Compatible Cisco IOS ReleaseHardware Revision Number Product Overviews Related DocumentationPort OC-12c/STM-4c ATM Line Card Overview Port OC-3c/STM-1 ATM Line Card Overview 101926 Safety Guidelines Preparing for InstallationRemoving and Installing a Line Card Preventing Electrostatic DischargeRequired Tools and Equipment Guidelines for Line Card Removal and Installation Removing a Line Card Line Card Removal and Installation Removing the Blank Filler Installing a Blank FillerInserting and Removing the Blank Filler Fastening Captive Screw on Blank Filler Installing a Line CardEjector Levers Removing and Installing a Line Card Line Card Cable-Management Bracket Line Card Cable-Management BracketMultiport Line Card Cable-Management Bracket Removing a Line Card Cable-Management Bracket 80220 Installing a Line Card Cable-Management Bracket Cabling and Specifications ATM Line Card Power Budget and Signal SpecificationsPort OC-12c/STM-4c ATM Line Card Power Specifications Attenuation Port OC-3c/STM-1 ATM Line Card Power SpecificationsTypical Maximum Transceiver DBm DistancePort OC-12c/STM-4c ISE ATM Line Card Power Specifications Port OC-3c/STM-1 ISE ATM Line Card Power SpecificationsFiber-Optic Network Interface Cables RX port TX port Duplex or simplex SC fiber cable connectors Initial Boot Process Verifying and Troubleshooting Line Card InstallationStatus LEDs Alphanumeric LEDsState Description Nnnn LED Display Meaning SourceVget IOS Done Fabl Troubleshooting the Installation Initial Configuration Configuring and Troubleshooting InterfacesConfiguring an Interface Parameter Configuration File Entry Default ValueRouter# show version Using show Commands to Check Status Using the show version CommandUsing the show gsr Command Using the show interfaces Command ATM Configuration ExampleUsing the show running-config Command Using ATM show CommandsOutput Examples Advanced Line Card TroubleshootingShow context summary Output Show context slot Output Checking the Current Status of the Line CardFabric Ping Failure Error MessagesFpga Error Messages Configuring and Troubleshooting Interfaces Configuring and Troubleshooting Interfaces Line Card Memory Locations Line Card MemoryEngine 0 and Engine 1 Line Card Memory Locations Engine 0 and Engine 1 Line Card Memory LocationsISE Line Card Memory Locations Engine 2 Line Card Memory LocationsLine Card Memory UpgradeLC-Slot3#show hardware ATM Line Card Route Memory OptionsRemoving and Installing Line Card Memory ATM Line Card Packet Memory OptionsCisco Product Number Dimm Modules Dimm Sockets Dimm Socket with Dual Release Levers Removing a DimmDimm Socket with Single Release Lever Installing a DimmHandling a Dimm Removing a SodimmRemove Retaining Clip from Memory Module Socket Using the Dimm Removal Tools to Release the Sodimm Removing a 144-pin Sodimm Module Sodimm Socket Retaining Clip Installing a SodimmSodimm with Key in Face-Up Position Inserting the Retaining Clip Retaining Clip Installed into Module Latch Checking the Installation of Line Card MemoryTranslated Safety Warnings and Agency Approvals Regulatory, Compliance, and Safety InformationElectromagnetic Compatibility Regulatory Statements FCC Class a ComplianceCanada Europe-EUVcci Class a Notice for Japan Regulatory, Compliance, and Safety Information Obtaining Documentation
Related manuals
Manual 263 pages 10.29 Kb