Cisco Systems 12000 series specifications Multiport Line Card Cable-Management Bracket

Page 18

Line Card Cable-Management Bracket

The cable-management system consists of two separate components:

1.A cable-management tray that is mounted on the chassis. Refer to the appropriate

Cisco 12000 Series Router installation and configuration guide for more information on the cable-management tray.

2.A cable-management bracket that attaches to a line card.

This section describes the line card cable-management bracket. Figure 11 shows the single-port line card cable-management bracket; Figure 12 shows the multiport line card cable-management bracket.

Figure 11

Single-Port Line Card Cable-Management Bracket

93237

Figure 12 Multiport Line Card Cable-Management Bracket

93238

ATM Line Card Installation and Configuration

18	OL-13004-01

Image 18

Contents ATM Line Card Installation and Configuration ContentsImportant Information Cisco IOS Software Release Requirements Router Hardware InstallationATM Line Card Product Numbers Supported PlatformsHardware Revision Requirements Compatible Cisco IOS ReleaseHardware Revision Number Product Overviews Related DocumentationPort OC-12c/STM-4c ATM Line Card Overview Port OC-3c/STM-1 ATM Line Card Overview 101926 Preparing for Installation Safety GuidelinesRemoving and Installing a Line Card Preventing Electrostatic DischargeRequired Tools and Equipment Guidelines for Line Card Removal and Installation Removing a Line Card Line Card Removal and Installation Installing a Blank Filler Removing the Blank FillerInserting and Removing the Blank Filler Installing a Line Card Fastening Captive Screw on Blank FillerEjector Levers Removing and Installing a Line Card Line Card Cable-Management Bracket Line Card Cable-Management BracketMultiport Line Card Cable-Management Bracket Removing a Line Card Cable-Management Bracket 80220 Installing a Line Card Cable-Management Bracket Cabling and Specifications ATM Line Card Power Budget and Signal SpecificationsPort OC-12c/STM-4c ATM Line Card Power Specifications Typical Maximum Port OC-3c/STM-1 ATM Line Card Power SpecificationsAttenuation Transceiver DBm DistancePort OC-12c/STM-4c ISE ATM Line Card Power Specifications Port OC-3c/STM-1 ISE ATM Line Card Power SpecificationsFiber-Optic Network Interface Cables RX port TX port Duplex or simplex SC fiber cable connectors Verifying and Troubleshooting Line Card Installation Initial Boot ProcessStatus LEDs Alphanumeric LEDsState Description LED Display Meaning Source NnnnVget IOS Done Fabl Troubleshooting the Installation Configuring an Interface Configuring and Troubleshooting InterfacesInitial Configuration Parameter Configuration File Entry Default ValueRouter# show version Using show Commands to Check Status Using the show version CommandUsing the show gsr Command Using the show running-config Command ATM Configuration ExampleUsing the show interfaces Command Using ATM show CommandsAdvanced Line Card Troubleshooting Output ExamplesShow context summary Output Checking the Current Status of the Line Card Show context slot OutputError Messages Fabric Ping FailureFpga Error Messages Configuring and Troubleshooting Interfaces Configuring and Troubleshooting Interfaces Line Card Memory Line Card Memory LocationsEngine 0 and Engine 1 Line Card Memory Locations Engine 0 and Engine 1 Line Card Memory LocationsEngine 2 Line Card Memory Locations ISE Line Card Memory LocationsMemory Upgrade Line CardATM Line Card Route Memory Options LC-Slot3#show hardwareRemoving and Installing Line Card Memory ATM Line Card Packet Memory OptionsCisco Product Number Dimm Modules Dimm Sockets Removing a Dimm Dimm Socket with Dual Release LeversInstalling a Dimm Dimm Socket with Single Release LeverRemoving a Sodimm Handling a DimmRemove Retaining Clip from Memory Module Socket Using the Dimm Removal Tools to Release the Sodimm Removing a 144-pin Sodimm Module Installing a Sodimm Sodimm Socket Retaining ClipSodimm with Key in Face-Up Position Inserting the Retaining Clip Checking the Installation of Line Card Memory Retaining Clip Installed into Module LatchElectromagnetic Compatibility Regulatory Statements Regulatory, Compliance, and Safety InformationTranslated Safety Warnings and Agency Approvals FCC Class a ComplianceCanada Europe-EUVcci Class a Notice for Japan Regulatory, Compliance, and Safety Information Obtaining Documentation

Related manuals

Manual 263 pages 10.29 Kb