Emulex 375 manual Power Supply/Fan Module LED

Page 14

EMULEX MODEL 375 SAN STORAGE SWITCH			CHAPTER 2: SWITCH INSTALLATION
USER’S GUIDE			CHAPTER 2: SWITCH INSTALLATION


	SFP Status	Port Bypassed
	LED	LED	Indication
	(green LED)	(yellow LED)

	Flashing	Off	Activity. Data is being transferred between the port and device.

	On	Off	Normal operation but no activity. Port and device are fully
			operational.

	On	Flashing	Manually bypassed. A port can be manually bypassed using the
			Web Manager’s Bypass Port feature.

	On	On	Bypassed. SFP is installed but the port is not receiving a valid
			signal or is receiving an F8 Failure notification from the attached
			device.

	Flashing	Flashing	Beaconing. This is set manually using the Web Manager or CLI.

Power Supply/Fan Module LED

The switch uses two power supply/fan modules to guarantee high availability with failover. Each power supply has a separate LED to indicate its condition.

	Power Supply/Fan Module LED	Indication
	(green LED)	Indication
	(green LED)

	On	No faults exist and AC power is supplied to the module.

	Off	A power supply or fan fault has occurred in the module.

When a power supply or fan fault occurs, the switch will continue to operate normally as long as the faulty power supply/fan module remains installed in the switch and there are at least two fans operational in each module. If the power supply/fan module is removed from the switch, the switch will continue to operate normally for approximately 20-30 minutes. However, to guarantee continued operation, the malfunctioning module should be immediately replaced to maintain high availability.

Note: Keeping spare power supply/fan modules (Part Number 601319) in stock is highly recommended. Contact a sales representative for further information.

EMULEX CORPORATION

11

PART NUMBER 00041392-002 REV. B

Image 14

Contents Emulex Model ART N Umber 00041392-002 R EV. B Table of Contents Chapter Introduction OverviewFeatures Inspeed TechnologySwitch Applications Storage Consolidation and Shared Storage Pooling3depicts a sample tape library consolidation configuration Tape Library ConsolidationRich Media Server ClusteringInstallation Preparation To unpack the switchSwitch Installation Rack InstallationDesktop Installation To place the switch on a desktopTo insert the power cord with the retention clip in place Installing the Retention Clips optionalTo install the retention clip To remove the power cord with the retention clip in placeEthernet LEDs indicate the network connection status Switch LedsEthernet LEDs System LEDs Port LEDsPower Supply/Fan Module LED Removing an SFP Installing an SFPAttaching a Device to the Switch SFP CompatibilityBooting the Switch and SAN To boot the switch and SANTo insert a new power supply/fan module Power SUPPLY/FAN Module ReplacementTo remove an old power supply/fan module Chapter Switch Management To connect through a serial interface Configuring the Network InterfaceGetting Started Web Manager Overview Connecting to the Web ManagerCommand Button Description Submit To connect to the Web ManagerLogin/Logout Command Button Description CancelReboot DocumentationChange the Password Initial Switch SetupLog in to the Switch To log in to the switchTo set the date and time settings Change the Switch NameTo view the current date and time Click Switch Date & Time To change the switch name Click Switch ConfigurationManaging the Switch Frequent Switch Configuration TasksTo change a switch setting Logging in to the SwitchConfiguring the Switch Settings To reset the switchNetwork Location General Switch SettingsSwitch Identification Version Information Switch SpeedTo change the switch speed Click Switch Configuration Blocking ARBSetting Snmp Traps To configure an Snmp trapTo synchronize time with the host system Click Host Time Configuring Date and Time SettingsTo change the time Click Switch Date & Time Opening a Telnet Session Changing the PasswordSwitch Password page appears To change switch thresholds or time intervals Adjusting the Switch ThresholdsSwitch Thresholds page appears Port Smart Settings page appears Configuring the Port Smart SettingsTo view the Port Smart Settings Click Port Smart Settings Default Smart Settings To set all ports to the currently selected Smart Setting Creating Custom Smart SettingsTo assign a Smart Setting to one or more ports To create a custom Smart SettingTo rename a custom Smart Setting Smart Setting AssignmentsTo modify a custom Smart Setting To delete a custom Smart SettingPort Information Pre-Insertion TestingFollowing settings are available Manager Setting Description Stealth Intelligent ChangeChange Notifications Change Notification onPort Recovery Bypass on Clock Delta DiagnosticsSetting Description Port Control To load new firmware on the switch Managing Firmware and Configuration FilesSwitch Firmware Files To check for new firmwareSwitch Configuration Files Restoring the Factory Default SettingsUp green One-Step ZoningColor Description Down red Not Active yellowSingle-Switch Zoning Adding Devices to Multiple Zones To add storage devices to multiple zonesMultiple Switch Zoning 16 Ports in Multiple Zones on the One-Step ZoningRecovering a Bad Zone Automatically Alpa ZoningConnecting Ports Through Hard Zoning To set up Hard ZoningTree Cascades Cascading SwitchesString Cascades Automatic Trunking 22 Automatic Trunking exampleLoad Balancing 23 Advanced Functions Automatic TrunkingLoad Indicators To change the load balancing settingsFairness and Prioritization Viewing Switch StatusMonitoring the Switch Switch Information Current status is provided for the following itemsYellow Port Utilization and HealthPort Color Indication Green RedEvent Log Messages page appears To view the event log Click Switch Event LogViewing the Event Log Last time the event log was polled appears at the topPort Information page appears Viewing Port InformationTo view port information Click Port Information Value Description High Viewing Port UtilizationPort Utilization page appears AverageViewing Port Diagnostics Port Diagnostics page appearsManual Port Operation To save diagnostic informationTo reset a port Click Advanced Functions Diagnostics Port To clear the countersViewing Ordered Sets Change CRC ErrorDetection Indication F7 Initialization Notification UnknownTroubleshooting Device Connections Troubleshooting Management Connections Port Bypass Conditions and RecoveryDefault Smart Setting Attributes Fibre Channel References Appendixes Switch Specifications Operating ConditionsTo connect through a network interface Connecting to the CLILogging in and OUT To log in to the CLIUsing the CLI Frequent Switch Configuration TasksCLI Commands Severity Description Level Event Event Message SeverityLIP Cycle Timeout Error during Port DiscPort Ptbi failed due to timeout System config reset to factory defaultArbitrated Loop Physical Addresses Hex DecimalArbitration Alpa or ArbitratedLoop Physical Address Current Fill WordIndex SFP Part Number 00041392-002 REV. B