Emulex 375 manual Booting the Switch and SAN, To boot the switch and SAN

Page 16

EMULEX MODEL 375 SAN STORAGE SWITCH	CHAPTER 2: SWITCH INSTALLATION
USER’S GUIDE

BOOTING THE SWITCH AND SAN

The following procedure is recommended when booting the switch and SAN. Before powering on the switch and SAN, read the Release Notes, included with the switch contents, to determine any modifications that may be required for a specific installation.

To boot the switch and SAN:

1.Power on the storage devices (such as JBODs, tape libraries, and RAIDs).

2.Insert the plug end of the switch’s power cord to a properly grounded power source.

3.Insert the power cord’s IEC connector end into the switch’s power receptacle.

The switch powers on and runs Power-On Self-Test (POST) diagnostics to verify the fundamental integrity of the switch ports. All switch LEDs turn on (LEDs illuminate). Then, excluding the Ethernet Link, Power Supply/Fan Module, and Power LEDs, the LEDs turn off (LEDs extinguish). Once the switch is operational, the LEDs display current status as described in “Switch LEDs” on page 9.

Note: The power cord’s IEC connector plug serves as the switch’s disconnect device. To cycle power to the switch, remove and reconnect the switch’s power cord.

4.Power on any other switches connected to the SAN.

5.For certain applications, switch configuration must be completed before continuing with the next step. For information regarding switch configuration, see Chapter 3: Switch Management.

6.After all switches have initialized, power on the hosts. The network initializes.

Note: FC-AL compatible nodes must perform initialization procedures upon power-up in order to function properly. It is the responsibility of the Fibre Channel driver software on FC-AL nodes to perform this initialization.

7.Check all port LEDs.

The SAN should be fully operational at this point. However, it is appropriate to ensure that proper discovery has taken place and all required devices are participating in the network. Some host bus adapters may provide this level of functionality or it might be resident in the application software on the host operating system.

EMULEX CORPORATION

13

PART NUMBER 00041392-002 REV. B

Image 16

Contents Emulex Model ART N Umber 00041392-002 R EV. B Table of Contents Chapter Introduction OverviewFeatures Inspeed TechnologySwitch Applications Storage Consolidation and Shared Storage Pooling3depicts a sample tape library consolidation configuration Tape Library ConsolidationRich Media Server ClusteringInstallation Preparation To unpack the switchRack Installation Desktop InstallationSwitch Installation To place the switch on a desktopInstalling the Retention Clips optional To install the retention clipTo insert the power cord with the retention clip in place To remove the power cord with the retention clip in placeEthernet LEDs Switch LedsEthernet LEDs indicate the network connection status System LEDs Port LEDsPower Supply/Fan Module LED Installing an SFP Attaching a Device to the SwitchRemoving an SFP SFP CompatibilityBooting the Switch and SAN To boot the switch and SANTo remove an old power supply/fan module Power SUPPLY/FAN Module ReplacementTo insert a new power supply/fan module Chapter Switch Management Getting Started Configuring the Network InterfaceTo connect through a serial interface Connecting to the Web Manager Command Button Description SubmitWeb Manager Overview To connect to the Web ManagerCommand Button Description Cancel RebootLogin/Logout DocumentationInitial Switch Setup Log in to the SwitchChange the Password To log in to the switchChange the Switch Name To view the current date and time Click Switch Date & TimeTo set the date and time settings To change the switch name Click Switch ConfigurationManaging the Switch Frequent Switch Configuration TasksLogging in to the Switch Configuring the Switch SettingsTo change a switch setting To reset the switchSwitch Identification General Switch SettingsNetwork Location Switch Speed To change the switch speed Click Switch ConfigurationVersion Information Blocking ARBSetting Snmp Traps To configure an Snmp trapTo change the time Click Switch Date & Time Configuring Date and Time SettingsTo synchronize time with the host system Click Host Time Switch Password page appears Changing the PasswordOpening a Telnet Session Switch Thresholds page appears Adjusting the Switch ThresholdsTo change switch thresholds or time intervals To view the Port Smart Settings Click Port Smart Settings Configuring the Port Smart SettingsPort Smart Settings page appears Default Smart Settings Creating Custom Smart Settings To assign a Smart Setting to one or more portsTo set all ports to the currently selected Smart Setting To create a custom Smart SettingSmart Setting Assignments To modify a custom Smart SettingTo rename a custom Smart Setting To delete a custom Smart SettingFollowing settings are available Pre-Insertion TestingPort Information Setting Description Stealth Intelligent Change Change NotificationsManager Change Notification onPort Recovery Setting Description Port Control DiagnosticsBypass on Clock Delta Managing Firmware and Configuration Files Switch Firmware FilesTo load new firmware on the switch To check for new firmwareSwitch Configuration Files Restoring the Factory Default SettingsOne-Step Zoning Color Description Down redUp green Not Active yellowSingle-Switch Zoning Adding Devices to Multiple Zones To add storage devices to multiple zonesMultiple Switch Zoning 16 Ports in Multiple Zones on the One-Step ZoningRecovering a Bad Zone Automatically Alpa ZoningConnecting Ports Through Hard Zoning To set up Hard ZoningString Cascades Cascading SwitchesTree Cascades Automatic Trunking 22 Automatic Trunking exampleLoad Balancing 23 Advanced Functions Automatic TrunkingLoad Indicators To change the load balancing settingsMonitoring the Switch Viewing Switch StatusFairness and Prioritization Switch Information Current status is provided for the following itemsPort Utilization and Health Port Color Indication GreenYellow RedTo view the event log Click Switch Event Log Viewing the Event LogEvent Log Messages page appears Last time the event log was polled appears at the topTo view port information Click Port Information Viewing Port InformationPort Information page appears Viewing Port Utilization Port Utilization page appearsValue Description High AverageViewing Port Diagnostics Port Diagnostics page appearsTo save diagnostic information To reset a port Click Advanced Functions Diagnostics PortManual Port Operation To clear the countersViewing Ordered Sets CRC Error Detection Indication F7 InitializationChange Notification UnknownTroubleshooting Device Connections Troubleshooting Management Connections Port Bypass Conditions and RecoveryDefault Smart Setting Attributes Fibre Channel References Appendixes Switch Specifications Operating ConditionsConnecting to the CLI Logging in and OUTTo connect through a network interface To log in to the CLIUsing the CLI Frequent Switch Configuration TasksCLI Commands Severity Description Level Event Event Message SeverityError during Port Disc Port Ptbi failed due to timeoutLIP Cycle Timeout System config reset to factory defaultArbitrated Loop Physical Addresses Hex DecimalAlpa or Arbitrated Loop Physical AddressArbitration Current Fill WordIndex SFP Part Number 00041392-002 REV. B