Emulex 375 manual General Switch Settings, Switch Identification, Network Location

Page 26

EMULEX MODEL 375 SAN STORAGE SWITCH	CHAPTER 3: SWITCH MANAGEMENT
USER’S GUIDE

General Switch Settings

The Switch Configuration page displays general settings and switch identification information.

To view the Switch Configuration page, click Switch > Configuration.

Figure 3-3: Switch Configuration page

Switch Identification

This section includes general switch identification information.

Setting	Description

Name	The name of the switch.

Location	The location of the switch.

Contact Name	The person or group to contact about the switch.

Serial Number	A unique identification number assigned to each switch at the factory. This
	setting cannot be configured or modified.

The name, location, and contact name information may be modified for the network environment. The Serial Number setting is factory set and cannot be modified.

To change the name, location, or contact name:

1.Click Switch > Configuration.

2.Enter the new value in the appropriate text box.

3.Click Submit.

The Switch Configuration page displays the updated information.

Network Location

The switch’s network location is identified by the IP Address, Netmask, and Gateway fields.

Setting	Description

Ethernet IP Address	The current IP Address for the switch.

Netmask	The current IP Netmask address for the switch.

Default Gateway	The current Gateway address for the switch.

EMULEX CORPORATION

23

PART NUMBER 00041392-002 REV. B

Image 26

Contents Emulex Model ART N Umber 00041392-002 R EV. B Table of Contents Chapter Introduction OverviewFeatures Inspeed TechnologySwitch Applications Storage Consolidation and Shared Storage Pooling3depicts a sample tape library consolidation configuration Tape Library ConsolidationRich Media Server ClusteringInstallation Preparation To unpack the switchSwitch Installation Rack InstallationDesktop Installation To place the switch on a desktopTo insert the power cord with the retention clip in place Installing the Retention Clips optionalTo install the retention clip To remove the power cord with the retention clip in placeEthernet LEDs indicate the network connection status Switch LedsEthernet LEDs System LEDs Port LEDsPower Supply/Fan Module LED Removing an SFP Installing an SFPAttaching a Device to the Switch SFP CompatibilityBooting the Switch and SAN To boot the switch and SANTo insert a new power supply/fan module Power SUPPLY/FAN Module ReplacementTo remove an old power supply/fan module Chapter Switch Management To connect through a serial interface Configuring the Network InterfaceGetting Started Web Manager Overview Connecting to the Web ManagerCommand Button Description Submit To connect to the Web ManagerLogin/Logout Command Button Description CancelReboot DocumentationChange the Password Initial Switch SetupLog in to the Switch To log in to the switchTo set the date and time settings Change the Switch NameTo view the current date and time Click Switch Date & Time To change the switch name Click Switch ConfigurationManaging the Switch Frequent Switch Configuration TasksTo change a switch setting Logging in to the SwitchConfiguring the Switch Settings To reset the switchNetwork Location General Switch SettingsSwitch Identification Version Information Switch SpeedTo change the switch speed Click Switch Configuration Blocking ARBSetting Snmp Traps To configure an Snmp trapTo synchronize time with the host system Click Host Time Configuring Date and Time SettingsTo change the time Click Switch Date & Time Opening a Telnet Session Changing the PasswordSwitch Password page appears To change switch thresholds or time intervals Adjusting the Switch ThresholdsSwitch Thresholds page appears Port Smart Settings page appears Configuring the Port Smart SettingsTo view the Port Smart Settings Click Port Smart Settings Default Smart Settings To set all ports to the currently selected Smart Setting Creating Custom Smart SettingsTo assign a Smart Setting to one or more ports To create a custom Smart SettingTo rename a custom Smart Setting Smart Setting AssignmentsTo modify a custom Smart Setting To delete a custom Smart SettingPort Information Pre-Insertion TestingFollowing settings are available Manager Setting Description Stealth Intelligent ChangeChange Notifications Change Notification onPort Recovery Bypass on Clock Delta DiagnosticsSetting Description Port Control To load new firmware on the switch Managing Firmware and Configuration FilesSwitch Firmware Files To check for new firmwareSwitch Configuration Files Restoring the Factory Default SettingsUp green One-Step ZoningColor Description Down red Not Active yellowSingle-Switch Zoning Adding Devices to Multiple Zones To add storage devices to multiple zonesMultiple Switch Zoning 16 Ports in Multiple Zones on the One-Step ZoningRecovering a Bad Zone Automatically Alpa ZoningConnecting Ports Through Hard Zoning To set up Hard ZoningTree Cascades Cascading SwitchesString Cascades Automatic Trunking 22 Automatic Trunking exampleLoad Balancing 23 Advanced Functions Automatic TrunkingLoad Indicators To change the load balancing settingsFairness and Prioritization Viewing Switch StatusMonitoring the Switch Switch Information Current status is provided for the following itemsYellow Port Utilization and HealthPort Color Indication Green RedEvent Log Messages page appears To view the event log Click Switch Event LogViewing the Event Log Last time the event log was polled appears at the topPort Information page appears Viewing Port InformationTo view port information Click Port Information Value Description High Viewing Port UtilizationPort Utilization page appears AverageViewing Port Diagnostics Port Diagnostics page appearsManual Port Operation To save diagnostic informationTo reset a port Click Advanced Functions Diagnostics Port To clear the countersViewing Ordered Sets Change CRC ErrorDetection Indication F7 Initialization Notification UnknownTroubleshooting Device Connections Troubleshooting Management Connections Port Bypass Conditions and RecoveryDefault Smart Setting Attributes Fibre Channel References Appendixes Switch Specifications Operating ConditionsTo connect through a network interface Connecting to the CLILogging in and OUT To log in to the CLIUsing the CLI Frequent Switch Configuration TasksCLI Commands Severity Description Level Event Event Message SeverityLIP Cycle Timeout Error during Port DiscPort Ptbi failed due to timeout System config reset to factory defaultArbitrated Loop Physical Addresses Hex DecimalArbitration Alpa or ArbitratedLoop Physical Address Current Fill WordIndex SFP Part Number 00041392-002 REV. B