Emulex 375 manual Installation Preparation, To unpack the switch

Page 9

EMULEX MODEL 375 SAN STORAGE SWITCH	CHAPTER 2: SWITCH INSTALLATION
USER’S GUIDE

CHAPTER 2 SWITCH INSTALLATION

Installation Preparation	6
Switch Installation	7
Switch LEDs	9
SFP Compatibility	12
Booting the Switch and SAN	13
Power Supply/Fan Module Replacement	14

INSTALLATION PREPARATION

After receiving the switch, perform the following steps to ensure that the switch and other contents arrived safely.

To unpack the switch:

1.Inspect the outer shipping container for any damage that may have occurred in shipping. Report any sign of damage to the appropriate shipping agency.

2.Remove the switch and cables from the shipping container; save the shipping container, foam, and antistatic bags—returning the switch in any other container is not advised.

Make sure the following parts are included:

•Switch unit

•RS-232 null-modem serial cable

•Power cables (2)

•Self-adhesive pads (4)

•Retention clips (2), screws (4), and washers (4) for securing the power cords to the switch.

•Quick Install Card

•Product Release Notes

•Safety and Regulatory Guide

•Additional documentation, including warranty information and the End User License Agreement.

3.Inspect the switch thoroughly. (If any signs of damage are seen, notify a sales representative and/or the shipping agency.)

EMULEX CORPORATION

6

PART NUMBER 00041392-002 REV. B

Image 9

Contents Emulex Model ART N Umber 00041392-002 R EV. B Table of Contents Overview Chapter IntroductionInspeed Technology FeaturesStorage Consolidation and Shared Storage Pooling Switch ApplicationsTape Library Consolidation 3depicts a sample tape library consolidation configurationServer Clustering Rich MediaTo unpack the switch Installation PreparationDesktop Installation Rack InstallationSwitch Installation To place the switch on a desktopTo install the retention clip Installing the Retention Clips optionalTo insert the power cord with the retention clip in place To remove the power cord with the retention clip in placeSwitch Leds Ethernet LEDsEthernet LEDs indicate the network connection status Port LEDs System LEDsPower Supply/Fan Module LED Attaching a Device to the Switch Installing an SFPRemoving an SFP SFP CompatibilityTo boot the switch and SAN Booting the Switch and SANPower SUPPLY/FAN Module Replacement To remove an old power supply/fan moduleTo insert a new power supply/fan module Chapter Switch Management Configuring the Network Interface Getting StartedTo connect through a serial interface Command Button Description Submit Connecting to the Web ManagerWeb Manager Overview To connect to the Web ManagerReboot Command Button Description CancelLogin/Logout DocumentationLog in to the Switch Initial Switch SetupChange the Password To log in to the switchTo view the current date and time Click Switch Date & Time Change the Switch NameTo set the date and time settings To change the switch name Click Switch ConfigurationFrequent Switch Configuration Tasks Managing the SwitchConfiguring the Switch Settings Logging in to the SwitchTo change a switch setting To reset the switchGeneral Switch Settings Switch IdentificationNetwork Location To change the switch speed Click Switch Configuration Switch SpeedVersion Information Blocking ARBTo configure an Snmp trap Setting Snmp TrapsConfiguring Date and Time Settings To change the time Click Switch Date & TimeTo synchronize time with the host system Click Host Time Changing the Password Switch Password page appearsOpening a Telnet Session Adjusting the Switch Thresholds Switch Thresholds page appearsTo change switch thresholds or time intervals Configuring the Port Smart Settings To view the Port Smart Settings Click Port Smart SettingsPort Smart Settings page appears Default Smart Settings To assign a Smart Setting to one or more ports Creating Custom Smart SettingsTo set all ports to the currently selected Smart Setting To create a custom Smart SettingTo modify a custom Smart Setting Smart Setting AssignmentsTo rename a custom Smart Setting To delete a custom Smart SettingPre-Insertion Testing Following settings are availablePort Information Change Notifications Setting Description Stealth Intelligent ChangeManager Change Notification onPort Recovery Diagnostics Setting Description Port ControlBypass on Clock Delta Switch Firmware Files Managing Firmware and Configuration FilesTo load new firmware on the switch To check for new firmwareRestoring the Factory Default Settings Switch Configuration FilesColor Description Down red One-Step ZoningUp green Not Active yellowSingle-Switch Zoning To add storage devices to multiple zones Adding Devices to Multiple Zones16 Ports in Multiple Zones on the One-Step Zoning Multiple Switch ZoningAlpa Zoning Recovering a Bad Zone AutomaticallyTo set up Hard Zoning Connecting Ports Through Hard ZoningCascading Switches String CascadesTree Cascades 22 Automatic Trunking example Automatic Trunking23 Advanced Functions Automatic Trunking Load BalancingTo change the load balancing settings Load IndicatorsViewing Switch Status Monitoring the SwitchFairness and Prioritization Current status is provided for the following items Switch InformationPort Color Indication Green Port Utilization and HealthYellow RedViewing the Event Log To view the event log Click Switch Event LogEvent Log Messages page appears Last time the event log was polled appears at the topViewing Port Information To view port information Click Port InformationPort Information page appears Port Utilization page appears Viewing Port UtilizationValue Description High AveragePort Diagnostics page appears Viewing Port DiagnosticsTo reset a port Click Advanced Functions Diagnostics Port To save diagnostic informationManual Port Operation To clear the countersViewing Ordered Sets Detection Indication F7 Initialization CRC ErrorChange Notification UnknownTroubleshooting Device Connections Port Bypass Conditions and Recovery Troubleshooting Management ConnectionsDefault Smart Setting Attributes Fibre Channel References Appendixes Operating Conditions Switch SpecificationsLogging in and OUT Connecting to the CLITo connect through a network interface To log in to the CLIFrequent Switch Configuration Tasks Using the CLICLI Commands Event Event Message Severity Severity Description LevelPort Ptbi failed due to timeout Error during Port DiscLIP Cycle Timeout System config reset to factory defaultHex Decimal Arbitrated Loop Physical AddressesLoop Physical Address Alpa or ArbitratedArbitration Current Fill WordIndex SFP Part Number 00041392-002 REV. B