Emulex 375 manual Port is ready to be inserted, Bad Open on Port #, Error during Port Disc

Page 72

EMULEX MODEL 375 SAN STORAGE SWITCH
USER’S GUIDE		APPENDIX C: EVENT MESSAGES


	Event	Event Message	Severity

	82	PORT is ready to be inserted	DBG

	83	Segment stall on PORT #	NOTIFY

	84	Bad Open on PORT #	WRN

	85	Error during Port Disc.	NOTIFY

	86	PORT PTBI failed due to timeout	NOTIFY

	87	PORT changed to STATE	NOTIFY

	88	Transceiver in PORT has been cycled	NOTIFY

	89	PORT has cycled between insert/bypassed (not necessarily in that	NOTIFY
		order)

	90	Loop CYCLED on Port #	NOTIFY

	91	Port exceeded Clk Delta threshold	INFO

	95	Interframe has been received	INFO

	96	Interswitch link added/removed	INFO

	97	LIP Cycle Timeout	INFO

	98	API Initialized OK	INFO

	99	Selftest failure	ERR

	100	Received Unknown event	INFO

	101	CRC detected on either an ISL LIP or Generic Frame	NOTIFY

	107	Trap task failed to update trap destination info.	CRIT

	135	CLI level 1 password changed	NOTIFY

	136	CLI level password changed to default setting	NOTIFY

	150	WEB level 1 password changed	NOTIFY

	151	Web password level changed to default setting	NOTIFY

	165	System config reset to factory default	ERR

	166	New Port Config Type added	NOTIFY

	167	Port Config Type deleted	NOTIFY

	168	Current Config saved to flash	NOTIFY

	169	Error in saving config file to flash	ERR

	170	Error in retrieving config information	ERR

	171	Config File successfully configured system	NOTIFY

	172	Error in initializing system with config file	ERR

	198	A device tried to access another device that was not in the same	NOTIFY
		zone

	199	Health timer has expired on ZONE	NOTIFY

	208	PORT is over threshold	NOTIFY

	218	Trunk DOWN on PORT #	NOTIFY

	219	Trunk UP on PORT #	NOTIFY

	220	New Primary Trunk	NOTIFY

EMULEX CORPORATION

69

PART NUMBER 00041392-002 REV. B

Image 72

Contents Emulex Model ART N Umber 00041392-002 R EV. B Table of Contents Chapter Introduction OverviewFeatures Inspeed TechnologySwitch Applications Storage Consolidation and Shared Storage Pooling3depicts a sample tape library consolidation configuration Tape Library ConsolidationRich Media Server ClusteringInstallation Preparation To unpack the switchRack Installation Desktop InstallationSwitch Installation To place the switch on a desktopInstalling the Retention Clips optional To install the retention clipTo insert the power cord with the retention clip in place To remove the power cord with the retention clip in placeSwitch Leds Ethernet LEDsEthernet LEDs indicate the network connection status System LEDs Port LEDsPower Supply/Fan Module LED Installing an SFP Attaching a Device to the SwitchRemoving an SFP SFP CompatibilityBooting the Switch and SAN To boot the switch and SANPower SUPPLY/FAN Module Replacement To remove an old power supply/fan moduleTo insert a new power supply/fan module Chapter Switch Management Configuring the Network Interface Getting StartedTo connect through a serial interface Connecting to the Web Manager Command Button Description SubmitWeb Manager Overview To connect to the Web ManagerCommand Button Description Cancel RebootLogin/Logout DocumentationInitial Switch Setup Log in to the SwitchChange the Password To log in to the switchChange the Switch Name To view the current date and time Click Switch Date & TimeTo set the date and time settings To change the switch name Click Switch ConfigurationManaging the Switch Frequent Switch Configuration TasksLogging in to the Switch Configuring the Switch SettingsTo change a switch setting To reset the switchGeneral Switch Settings Switch IdentificationNetwork Location Switch Speed To change the switch speed Click Switch ConfigurationVersion Information Blocking ARBSetting Snmp Traps To configure an Snmp trapConfiguring Date and Time Settings To change the time Click Switch Date & TimeTo synchronize time with the host system Click Host Time Changing the Password Switch Password page appearsOpening a Telnet Session Adjusting the Switch Thresholds Switch Thresholds page appearsTo change switch thresholds or time intervals Configuring the Port Smart Settings To view the Port Smart Settings Click Port Smart SettingsPort Smart Settings page appears Default Smart Settings Creating Custom Smart Settings To assign a Smart Setting to one or more portsTo set all ports to the currently selected Smart Setting To create a custom Smart SettingSmart Setting Assignments To modify a custom Smart SettingTo rename a custom Smart Setting To delete a custom Smart SettingPre-Insertion Testing Following settings are availablePort Information Setting Description Stealth Intelligent Change Change NotificationsManager Change Notification onPort Recovery Diagnostics Setting Description Port ControlBypass on Clock Delta Managing Firmware and Configuration Files Switch Firmware FilesTo load new firmware on the switch To check for new firmwareSwitch Configuration Files Restoring the Factory Default SettingsOne-Step Zoning Color Description Down redUp green Not Active yellowSingle-Switch Zoning Adding Devices to Multiple Zones To add storage devices to multiple zonesMultiple Switch Zoning 16 Ports in Multiple Zones on the One-Step ZoningRecovering a Bad Zone Automatically Alpa ZoningConnecting Ports Through Hard Zoning To set up Hard ZoningCascading Switches String CascadesTree Cascades Automatic Trunking 22 Automatic Trunking exampleLoad Balancing 23 Advanced Functions Automatic TrunkingLoad Indicators To change the load balancing settingsViewing Switch Status Monitoring the SwitchFairness and Prioritization Switch Information Current status is provided for the following itemsPort Utilization and Health Port Color Indication GreenYellow RedTo view the event log Click Switch Event Log Viewing the Event LogEvent Log Messages page appears Last time the event log was polled appears at the topViewing Port Information To view port information Click Port InformationPort Information page appears Viewing Port Utilization Port Utilization page appearsValue Description High AverageViewing Port Diagnostics Port Diagnostics page appearsTo save diagnostic information To reset a port Click Advanced Functions Diagnostics PortManual Port Operation To clear the countersViewing Ordered Sets CRC Error Detection Indication F7 InitializationChange Notification UnknownTroubleshooting Device Connections Troubleshooting Management Connections Port Bypass Conditions and RecoveryDefault Smart Setting Attributes Fibre Channel References Appendixes Switch Specifications Operating ConditionsConnecting to the CLI Logging in and OUTTo connect through a network interface To log in to the CLIUsing the CLI Frequent Switch Configuration TasksCLI Commands Severity Description Level Event Event Message SeverityError during Port Disc Port Ptbi failed due to timeoutLIP Cycle Timeout System config reset to factory defaultArbitrated Loop Physical Addresses Hex DecimalAlpa or Arbitrated Loop Physical AddressArbitration Current Fill WordIndex SFP Part Number 00041392-002 REV. B