Cabletron Systems SEHI100TX manual Rack Mounting Capabilities, Remote Network Management

Page 15

Chapter 2: SEHI Features and Options

2.4RACK MOUNTING CAPABILITIES

The SEHI can be installed in a 19-inch rack. Cabletron Systems provides brackets and mounting screws with the SEHI. See Chapter 4, Installation, for complete rack mounting instructions.

2.5REMOTE NETWORK MANAGEMENT

Manage the SEHI remotely with any SNMP network management system. Cabletron Systems offers the following remote management packages:

•Cabletron Systems SPECTRUM

•Cabletron Systems SPECTRUM Element Manager/Windows

•Cabletron Systems Remote SPECTRUM Portable Management Applications

•Third Party SNMP compliant Network Management Packages

2.6OPTIONAL 100BASE-TX and 100BASE-FX EPIMs

100BASE-TX and 100BASE-FX EPIMs are not included with the SEHI but can be purchased separately from Cabletron Systems.

EPIMs enable the expansion of a network through different types of media. Cabletron Systems offers two optional EPIMs for the SEHI100TX-22 and the SEH100TX-22 as shown in Table 2-1.

Table 2-1 100BASE-TX/FX EPIMs

EPIM	Media Type	Connector


EPIM-100TX	Category 5 UTP Cable	RJ45

EPIM-100FX	Multimode Fiber Optic Cable	SC

2-4	SEHI100TX User’s Guide

Image 15

Contents Intelligent Stackable HUB USER’S Guide SEHI100TX User’s Guide FCC Notice Cabletron SYSTEMS, INC. Program License Agreement United States Government Restricted Rights Contents Contents SEHI100TX User’s Guide Vii Chapter Introduction Using this ManualFollowing conventions are used throughout this document Document ConventionsRelated Manuals Getting Help Sehi Overview Chapter Sehi Features and OptionsSehi Features and Options Sehi FeaturesStackable Capabilities Rack Mounting Capabilities Remote Network ManagementOptional 100BASE-TX and 100BASE-FX EPIMs Chapter Installation Requirements Specifications Cable SpecificationsHubSTACK Interconnect Cable Requirements UTP Cable Speciﬁcations Multimode Speciﬁcations for the EPIM-100FX Network Cable Lengths COM Port Requirements Network Port SpecificationsOperating Specifications Power Supply RequirementsEnvironmental Requirements Agency Approvals Physical SpecificationsUnpacking the Sehi Chapter InstallationNvram Switch Location PRE-INSTALLATION CheckoutSEHI100TX-22 Tabletop or Shelf InstallationScrews Strain-Relief Bracket Rackmount InstallationRackmount Installation Installing the Sehi in the Rack Powering UP and Stacking the Sehi Repeat steps 3 through 6 until all SEH hubs are connected Install an EPIM-100TX or an EPIM-100FX as follows Installing the EPIM-100TX or the EPIM-100FXChapter Connecting to the Network Connecting the Sehi to the NetworkConnecting to Network Ports Sehi Network Ports Connecting a UTP Segment to an EPIM-100TXPosition X crossed over RX+ TX+ Position = Not crossed over EPIM-100FX Port Connecting a Fiber Segment to the EPIM-100FXTesting the Installation Installation Test Chapter TroubleshootingUsing Lanview Using Lanview Epim 1 RCV LED Using the Reset ButtonSetting the Nvram Switch Chapter Local Management Keyboard Conventions Function Local Management Keyboard ConventionsManagement Terminal Setup Console Cable Conﬁguration Management Terminal Setup Parameters Sehi Local Management Accessing Local ManagementFeature Selection Screen Feature Selection ScreenCommunity Name Table Screen Community Name Table ScreenEditing the Community Name Field Configuration Configuration ScreenDisplays the IP address of the Sehi Setting the Subnet Mask Setting the IP AddressUsing the Port Enable Override Setting the Default GatewayTrap Table Screen Exiting the Conﬁguration ScreenExiting the Trap Table Screen 1 Conﬁguring the Trap TableSnmp Tools Screen Snmp Tools ScreenLets you retrieve MIB objects using Snmp protocol Setting an OID Getting Individual OIDsGetting the Next OID Walking Through OIDs Viewing Multiple OIDsStepping Through OIDs Cycling Through OIDsExiting the Snmp Tools Screen Device Statistics Screen Device Statistics ScreenDisplays the number of errors due to misaligned packets Module Number Sequence Selecting the Appropriate Module/PortUsing the Enable Port Command Using the Disable Port CommandExiting the Device Statistics Screen Appendix a Epim Specifications Epim SpecificationsEPIM-100TX EPIM-100FX Appendix B Image File Download Using Oids Setting UP a Unix Workstation AS a Tftp Server Standard Local Download Table B-1 OIDs and Settings Numerics IndexIndex-2 Power Supply Cord