Cabletron Systems SEHI100TX manual Stepping Through OIDs, Cycling Through OIDs

Page 61

Chapter 7: Local Management

7.8.6Stepping Through OIDs

Use the following steps to STEP through OIDs (the user can step through only after a GETNEXT):

1.Highlight STEP, using the arrow keys, then press ENTER. “Specify OID” appears.

2.Enter the OID (only the suffix is necessary) and press ENTER. The Tools screen will begin to scroll one OID at a time, through all of the sublayers of the MIB available for that OID.

7.8.7Cycling Through OIDs

Use the following steps to CYCLE through an OID:

1.Use the arrow keys to Highlight CYCLES, then press ENTER.

2.Enter the number of cycles desired to occur after “ENTER CYCLE COUNT:”, then press ENTER.

3.Enter how many seconds delay desired between get next requests after “ENTER CYCLE DELAY (secs):”, then press ENTER.

7.8.8Exiting the SNMP Tools Screen

To exit the SNMP Tools Screen:

1.Use the arrow keys to highlight the RETURN command.

2.Press ENTER. The Feature Selection screen appears.

7-20	SEHI100TX User’s Guide

Image 61

Contents Intelligent Stackable HUB USER’S Guide SEHI100TX User’s Guide FCC Notice Cabletron SYSTEMS, INC. Program License Agreement United States Government Restricted Rights Contents Contents SEHI100TX User’s Guide Vii Chapter Introduction Using this ManualFollowing conventions are used throughout this document Document ConventionsRelated Manuals Getting HelpSehi Overview Chapter Sehi Features and OptionsSehi Features and Options Sehi FeaturesStackable Capabilities Remote Network Management Rack Mounting CapabilitiesOptional 100BASE-TX and 100BASE-FX EPIMs Cable Specifications Chapter Installation Requirements SpecificationsHubSTACK Interconnect Cable Requirements UTP Cable Speciﬁcations Multimode Speciﬁcations for the EPIM-100FX Network Cable Lengths COM Port Requirements Network Port SpecificationsPower Supply Requirements Operating SpecificationsEnvironmental Requirements Agency Approvals Physical SpecificationsUnpacking the Sehi Chapter InstallationNvram Switch Location PRE-INSTALLATION CheckoutSEHI100TX-22 Tabletop or Shelf InstallationScrews Strain-Relief Bracket Rackmount InstallationRackmount Installation Installing the Sehi in the Rack Powering UP and Stacking the Sehi Repeat steps 3 through 6 until all SEH hubs are connected Install an EPIM-100TX or an EPIM-100FX as follows Installing the EPIM-100TX or the EPIM-100FXConnecting the Sehi to the Network Chapter Connecting to the NetworkConnecting to Network Ports Sehi Network Ports Connecting a UTP Segment to an EPIM-100TXPosition X crossed over RX+ TX+ Position = Not crossed over EPIM-100FX Port Connecting a Fiber Segment to the EPIM-100FXTesting the Installation Installation Test Chapter TroubleshootingUsing Lanview Using Lanview Epim 1 RCV LED Using the Reset ButtonSetting the Nvram Switch Chapter Local Management Keyboard Conventions Function Local Management Keyboard ConventionsManagement Terminal Setup Console Cable Conﬁguration Management Terminal Setup Parameters Sehi Local Management Accessing Local ManagementFeature Selection Screen Feature Selection ScreenCommunity Name Table Screen Community Name Table ScreenEditing the Community Name Field Configuration Configuration ScreenDisplays the IP address of the Sehi Setting the Subnet Mask Setting the IP AddressUsing the Port Enable Override Setting the Default GatewayTrap Table Screen Exiting the Conﬁguration ScreenExiting the Trap Table Screen 1 Conﬁguring the Trap TableSnmp Tools Screen Snmp Tools ScreenLets you retrieve MIB objects using Snmp protocol Getting Individual OIDs Setting an OIDGetting the Next OID Walking Through OIDs Viewing Multiple OIDsCycling Through OIDs Stepping Through OIDsExiting the Snmp Tools Screen Device Statistics Screen Device Statistics ScreenDisplays the number of errors due to misaligned packets Module Number Sequence Selecting the Appropriate Module/PortUsing the Disable Port Command Using the Enable Port CommandExiting the Device Statistics Screen Epim Specifications Appendix a Epim SpecificationsEPIM-100TX EPIM-100FX Appendix B Image File Download Using Oids Setting UP a Unix Workstation AS a Tftp Server Standard Local Download Table B-1 OIDs and Settings Numerics IndexIndex-2 Power Supply Cord