Cabletron Systems SEHI100TX manual Power Supply Cord

Page 74

POWER SUPPLY CORD

The mains cord used with this equipment must be a 2 conductor plus ground type with minimum 0.75 mm square conductors and must incorporate a standard IEC appliance coupler on one end and a mains plug on the other end which is suitable for the use and application of the product and that is approved for use in the country of application.

GERMAN:

Die Netzleitung, die mit diesem Geraet benuetzt wird, soll einen zwei Leiter mit Erdleiter haben, wobei die Leiter mindestens 0.75 mm sind, mit einer normalen IEC Geraetesteckdose an einem Ende und einem Geraetestecker am anderen Ende versehen sind, der fuer den Gebrauch und die Anwendung des Geraetes geeignet und der zum Benuetzen im Lande der Anwendung anerkannt ist.

SPANISH:

El cable principal de la red eléctrica utilizado con este equipo debe tener 2 conductores y 1 toma de tierra con un mínimo de 0.75 mm2 cada uno y necesita tener un aparato de acoplamiento standard IEC en un extremo y un enchufe para el cable principal de la red eléctrica en el otro extremo, lo cual sea adecuado para el uso y applicación del producto y lo cual sea aprobado para uso en el pais de applicación.

FRENCH:

Le cordon d' alimentation reliant cet appareil au secteur doit obligatoirement avoir deux fils conducteurs de 0.75 mm2 minimum et un fil de terre. It doit également être équipé du côté appareil d'une fiche agrée IEC et du côte secteur, d'une prise adaptée à l'usage du produit et aux normes du pays où l'appareil est utilisé.

Image 74
Contents Intelligent Stackable HUB USER’S Guide SEHI100TX User’s Guide FCC Notice Cabletron SYSTEMS, INC. Program License Agreement United States Government Restricted Rights Contents Contents SEHI100TX User’s Guide Vii Using this Manual Chapter IntroductionDocument Conventions Following conventions are used throughout this documentGetting Help Related ManualsChapter Sehi Features and Options Sehi OverviewSehi Features Sehi Features and OptionsStackable Capabilities Optional 100BASE-TX and 100BASE-FX EPIMs Rack Mounting CapabilitiesRemote Network Management HubSTACK Interconnect Cable Requirements Chapter Installation Requirements SpecificationsCable Specifications UTP Cable Specifications Multimode Specifications for the EPIM-100FX Network Cable Lengths Network Port Specifications COM Port RequirementsEnvironmental Requirements Operating SpecificationsPower Supply Requirements Physical Specifications Agency ApprovalsChapter Installation Unpacking the SehiPRE-INSTALLATION Checkout Nvram Switch LocationTabletop or Shelf Installation SEHI100TX-22Rackmount Installation Screws Strain-Relief BracketRackmount Installation Installing the Sehi in the Rack Powering UP and Stacking the Sehi Repeat steps 3 through 6 until all SEH hubs are connected Installing the EPIM-100TX or the EPIM-100FX Install an EPIM-100TX or an EPIM-100FX as followsConnecting to Network Ports Chapter Connecting to the NetworkConnecting the Sehi to the Network Connecting a UTP Segment to an EPIM-100TX Sehi Network PortsPosition X crossed over RX+ TX+ Position = Not crossed over Connecting a Fiber Segment to the EPIM-100FX EPIM-100FX PortTesting the Installation Chapter Troubleshooting Installation TestUsing Lanview Using Lanview Using the Reset Button Epim 1 RCV LEDSetting the Nvram Switch Chapter Local Management Local Management Keyboard Conventions Keyboard Conventions FunctionManagement Terminal Setup Console Cable Configuration Management Terminal Setup Parameters Accessing Local Management Sehi Local ManagementFeature Selection Screen Feature Selection ScreenCommunity Name Table Screen Community Name Table ScreenEditing the Community Name Field Configuration Screen ConfigurationDisplays the IP address of the Sehi Setting the IP Address Setting the Subnet MaskSetting the Default Gateway Using the Port Enable OverrideExiting the Configuration Screen Trap Table Screen1 Configuring the Trap Table Exiting the Trap Table ScreenSnmp Tools Screen Snmp Tools ScreenLets you retrieve MIB objects using Snmp protocol Getting the Next OID Setting an OIDGetting Individual OIDs Viewing Multiple OIDs Walking Through OIDsExiting the Snmp Tools Screen Stepping Through OIDsCycling Through OIDs Device Statistics Screen Device Statistics ScreenDisplays the number of errors due to misaligned packets Selecting the Appropriate Module/Port Module Number SequenceExiting the Device Statistics Screen Using the Enable Port CommandUsing the Disable Port Command EPIM-100TX Appendix a Epim SpecificationsEpim Specifications EPIM-100FX Appendix B Image File Download Using Oids Setting UP a Unix Workstation AS a Tftp Server Standard Local Download Table B-1 OIDs and Settings Index NumericsIndex-2 Power Supply Cord