Cabletron Systems SEHI100TX manual Configuration Screen

Page 51

Chapter 7: Local Management

NOTE

The ﬁrst time a user attempts to exit the screen without saving the changes, a “NOT SAVED?” message is displayed. The edits are lost if the user proceeds to exit without saving the changes.

6.To exit the screen, press the appropriate Function key or use the arrow keys to highlight the RETURN command.

7.Press ENTER. The Feature Selection screen appears.

7.6THE CONFIGURATION SCREEN

To access the Conﬁguration screen from the Feature Selection screen, use the arrow keys to highlight the IP Address Assignment option, then press ENTER or F7. The screen shown in Figure 7-5 appears.

SEHI LOCAL MANAGEMENT

Cabletron SEHI Revision X.XX.XX

CONFIGURATION

I/F	IP Address	SubNET Mask	MAC Address
1	000.000.000.000	000.000.000.000	00-00-1d-05-dc-36

	Default Gateway: 0.0.0.0
	Serial Port 1 Application: CONSOLE		Baud Rate: 9600 --ACTIVE-
	-
	Port Enable Override: OVERRIDE DISABLED
SAVE	COMMUNITY NAMES	TRAP TABLE	SNMP TOOLS	RETURN
F6	F7	F8	F9

1490_24

Figure 7-5 Conﬁguration Screen

Assign the IP Address, Subnet Mask, and Default Gateway through the SEHI Conﬁguration screen. Use the Port Enable Override option to enable all device ports in the stack. This option overrides the Port Disable setting in the Statistics screen.

The following sections explain each ﬁeld on the Conﬁguration screen and instructions on how to change them.

7-10	SEHI100TX User’s Guide

Image 51

Contents Intelligent Stackable HUB USER’S Guide SEHI100TX User’s Guide FCC Notice Cabletron SYSTEMS, INC. Program License Agreement United States Government Restricted Rights Contents Contents SEHI100TX User’s Guide Vii Chapter Introduction Using this ManualFollowing conventions are used throughout this document Document ConventionsRelated Manuals Getting HelpSehi Overview Chapter Sehi Features and OptionsSehi Features and Options Sehi FeaturesStackable Capabilities Rack Mounting Capabilities Remote Network ManagementOptional 100BASE-TX and 100BASE-FX EPIMs Chapter Installation Requirements Specifications Cable SpecificationsHubSTACK Interconnect Cable Requirements UTP Cable Speciﬁcations Multimode Speciﬁcations for the EPIM-100FX Network Cable Lengths COM Port Requirements Network Port SpecificationsOperating Specifications Power Supply RequirementsEnvironmental Requirements Agency Approvals Physical SpecificationsUnpacking the Sehi Chapter InstallationNvram Switch Location PRE-INSTALLATION CheckoutSEHI100TX-22 Tabletop or Shelf InstallationScrews Strain-Relief Bracket Rackmount InstallationRackmount Installation Installing the Sehi in the Rack Powering UP and Stacking the Sehi Repeat steps 3 through 6 until all SEH hubs are connected Install an EPIM-100TX or an EPIM-100FX as follows Installing the EPIM-100TX or the EPIM-100FXChapter Connecting to the Network Connecting the Sehi to the NetworkConnecting to Network Ports Sehi Network Ports Connecting a UTP Segment to an EPIM-100TXPosition X crossed over RX+ TX+ Position = Not crossed over EPIM-100FX Port Connecting a Fiber Segment to the EPIM-100FXTesting the Installation Installation Test Chapter TroubleshootingUsing Lanview Using Lanview Epim 1 RCV LED Using the Reset ButtonSetting the Nvram Switch Chapter Local Management Keyboard Conventions Function Local Management Keyboard ConventionsManagement Terminal Setup Console Cable Conﬁguration Management Terminal Setup Parameters Sehi Local Management Accessing Local ManagementFeature Selection Screen Feature Selection ScreenCommunity Name Table Screen Community Name Table ScreenEditing the Community Name Field Configuration Configuration ScreenDisplays the IP address of the Sehi Setting the Subnet Mask Setting the IP AddressUsing the Port Enable Override Setting the Default GatewayTrap Table Screen Exiting the Conﬁguration ScreenExiting the Trap Table Screen 1 Conﬁguring the Trap TableSnmp Tools Screen Snmp Tools ScreenLets you retrieve MIB objects using Snmp protocol Setting an OID Getting Individual OIDsGetting the Next OID Walking Through OIDs Viewing Multiple OIDsStepping Through OIDs Cycling Through OIDsExiting the Snmp Tools Screen Device Statistics Screen Device Statistics ScreenDisplays the number of errors due to misaligned packets Module Number Sequence Selecting the Appropriate Module/PortUsing the Enable Port Command Using the Disable Port CommandExiting the Device Statistics Screen Appendix a Epim Specifications Epim SpecificationsEPIM-100TX EPIM-100FX Appendix B Image File Download Using Oids Setting UP a Unix Workstation AS a Tftp Server Standard Local Download Table B-1 OIDs and Settings Numerics IndexIndex-2 Power Supply Cord