Cabletron Systems SEHI100TX manual Snmp Tools Screen

Page 57

Chapter 7: Local Management

7.8THE SNMP TOOLS SCREEN

This section describes how to use the SNMP Tools screen to access Management Information Bases (MIBs). Access to screen options depends on the access status accorded to the user’s community name. This section describes Super-User management capabilities.

SNMP Tools allows access to valuable MIB information. The user gets information about speciﬁc object identiﬁers (OIDs), edit the values of conﬁgurable OIDs, and request the OID numerically sequential to the originally requested OID.

Other ways to view OIDs from the SNMP Tools screen include Walking, Stepping, and Cycling. Walk and Cycle let the user review several OIDs at a time.

To access the SNMP Tools screen from the Features Selection screen, use the arrow keys to highlight the SNMP Tools Support option, then press ENTER or F9. The SNMP Tools screen shown in Figure 7-7 appears.

SEHI LOCAL MANAGEMENT

Cabletron SEHI Revision X.XX.XX

SNMP TOOLS

SNMP COMMUNITY NAME: public

OID PREPEND: 1.3.6.1

GET	SET	GETNEXT WALK	RECALL-OID STEP CYCLES REPEAT
F6	F7	F8	F9

RETURN

F10

1490_26

Figure 7-7 SNMP Tools Screen

The following sections describe SNMP Tools screen ﬁelds.

SNMP COMMUNITY NAME

Identiﬁes the community name used as a password to determine access level to the MIB component.

7-16	SEHI100TX User’s Guide

Image 57

Contents Intelligent Stackable HUB USER’S Guide SEHI100TX User’s Guide FCC Notice Cabletron SYSTEMS, INC. Program License Agreement United States Government Restricted Rights Contents Contents SEHI100TX User’s Guide Vii Chapter Introduction Using this ManualFollowing conventions are used throughout this document Document ConventionsRelated Manuals Getting HelpSehi Overview Chapter Sehi Features and OptionsSehi Features and Options Sehi FeaturesStackable Capabilities Rack Mounting Capabilities Remote Network ManagementOptional 100BASE-TX and 100BASE-FX EPIMs Chapter Installation Requirements Specifications Cable SpecificationsHubSTACK Interconnect Cable Requirements UTP Cable Speciﬁcations Multimode Speciﬁcations for the EPIM-100FX Network Cable Lengths COM Port Requirements Network Port SpecificationsOperating Specifications Power Supply RequirementsEnvironmental Requirements Agency Approvals Physical SpecificationsUnpacking the Sehi Chapter InstallationNvram Switch Location PRE-INSTALLATION CheckoutSEHI100TX-22 Tabletop or Shelf InstallationScrews Strain-Relief Bracket Rackmount InstallationRackmount Installation Installing the Sehi in the Rack Powering UP and Stacking the Sehi Repeat steps 3 through 6 until all SEH hubs are connected Install an EPIM-100TX or an EPIM-100FX as follows Installing the EPIM-100TX or the EPIM-100FXChapter Connecting to the Network Connecting the Sehi to the NetworkConnecting to Network Ports Sehi Network Ports Connecting a UTP Segment to an EPIM-100TXPosition X crossed over RX+ TX+ Position = Not crossed over EPIM-100FX Port Connecting a Fiber Segment to the EPIM-100FXTesting the Installation Installation Test Chapter TroubleshootingUsing Lanview Using Lanview Epim 1 RCV LED Using the Reset ButtonSetting the Nvram Switch Chapter Local Management Keyboard Conventions Function Local Management Keyboard ConventionsManagement Terminal Setup Console Cable Conﬁguration Management Terminal Setup Parameters Sehi Local Management Accessing Local ManagementFeature Selection Screen Feature Selection ScreenCommunity Name Table Screen Community Name Table ScreenEditing the Community Name Field Configuration Configuration ScreenDisplays the IP address of the Sehi Setting the Subnet Mask Setting the IP AddressUsing the Port Enable Override Setting the Default GatewayTrap Table Screen Exiting the Conﬁguration ScreenExiting the Trap Table Screen 1 Conﬁguring the Trap TableSnmp Tools Screen Snmp Tools ScreenLets you retrieve MIB objects using Snmp protocol Setting an OID Getting Individual OIDsGetting the Next OID Walking Through OIDs Viewing Multiple OIDsStepping Through OIDs Cycling Through OIDsExiting the Snmp Tools Screen Device Statistics Screen Device Statistics ScreenDisplays the number of errors due to misaligned packets Module Number Sequence Selecting the Appropriate Module/PortUsing the Enable Port Command Using the Disable Port CommandExiting the Device Statistics Screen Appendix a Epim Specifications Epim SpecificationsEPIM-100TX EPIM-100FX Appendix B Image File Download Using Oids Setting UP a Unix Workstation AS a Tftp Server Standard Local Download Table B-1 OIDs and Settings Numerics IndexIndex-2 Power Supply Cord