Cabletron Systems SEHI100TX manual Exiting the Configuration Screen, Trap Table Screen

Page 55

Chapter 7: Local Management

7.6.5Exiting the Configuration Screen

Use the following steps to exit the Configuration screen and return to the Feature Selection screen:

1.Press the appropriate Function key. To return to the Feature Selection screen, use the arrow keys to highlight the RETURN command.

2.Press ENTER. The Feature Selection screen appears.

7.7THE TRAP TABLE SCREEN

Access the Trap Table screen from the Features Selection screen using the arrow keys to highlight the Component Trap Table option, then press ENTER or F8. The screen shown in Figure 7-6 appears.

SEHI LOCAL MANAGEMENT

Cabletron SEHI Revision X.XX.XX

TRAP TABLE

SNMP Community Name

 

Traps

IP Address

 

 

 

 

 

<CR>

 

 

N

0.0.0.0

 

 

 

<CR>

 

 

N

0.0.0.0

 

 

 

<CR>

 

 

N

0.0.0.0

 

 

 

<CR>

 

 

N

0.0.0.0

 

 

 

<CR>

 

 

N

0.0.0.0

 

 

 

<CR>

 

 

N

0.0.0.0

 

 

 

<CR>

 

 

N

0.0.0.0

 

 

 

<CR>

 

 

N

0.0.0.0

 

 

 

SAVE

COMMUNITY NAMES

IP TABLE

SNMP TOOLS

RETURN

F6

F7

F8

F9

 

1490_25

Figure 7-6 Trap Table Screen

The Trap Table defines the management stations that receive SNMP Traps for alarm/event notification. The following sections explain each field on the Trap Table screen and provide instructions on how to change them.

SNMP Community Name

Displays the community name included in the trap message sent to the Network Management Station with the associated IP address.

7-14

SEHI100TX User’s Guide

Image 55
Contents Intelligent Stackable HUB USER’S Guide SEHI100TX User’s Guide FCC Notice Cabletron SYSTEMS, INC. Program License Agreement United States Government Restricted Rights Contents Contents SEHI100TX User’s Guide Vii Chapter Introduction Using this ManualFollowing conventions are used throughout this document Document ConventionsRelated Manuals Getting HelpSehi Overview Chapter Sehi Features and OptionsSehi Features and Options Sehi FeaturesStackable Capabilities Remote Network Management Rack Mounting CapabilitiesOptional 100BASE-TX and 100BASE-FX EPIMs Cable Specifications Chapter Installation Requirements SpecificationsHubSTACK Interconnect Cable Requirements UTP Cable Specifications Multimode Specifications for the EPIM-100FX Network Cable Lengths COM Port Requirements Network Port SpecificationsPower Supply Requirements Operating SpecificationsEnvironmental Requirements Agency Approvals Physical SpecificationsUnpacking the Sehi Chapter InstallationNvram Switch Location PRE-INSTALLATION CheckoutSEHI100TX-22 Tabletop or Shelf InstallationScrews Strain-Relief Bracket Rackmount InstallationRackmount Installation Installing the Sehi in the Rack Powering UP and Stacking the Sehi Repeat steps 3 through 6 until all SEH hubs are connected Install an EPIM-100TX or an EPIM-100FX as follows Installing the EPIM-100TX or the EPIM-100FXConnecting the Sehi to the Network Chapter Connecting to the NetworkConnecting to Network Ports Sehi Network Ports Connecting a UTP Segment to an EPIM-100TXPosition X crossed over RX+ TX+ Position = Not crossed over EPIM-100FX Port Connecting a Fiber Segment to the EPIM-100FXTesting the Installation Installation Test Chapter TroubleshootingUsing Lanview Using Lanview Epim 1 RCV LED Using the Reset ButtonSetting the Nvram Switch Chapter Local Management Keyboard Conventions Function Local Management Keyboard ConventionsManagement Terminal Setup Console Cable Configuration Management Terminal Setup Parameters Sehi Local Management Accessing Local ManagementFeature Selection Screen Feature Selection ScreenCommunity Name Table Screen Community Name Table ScreenEditing the Community Name Field Configuration Configuration ScreenDisplays the IP address of the Sehi Setting the Subnet Mask Setting the IP AddressUsing the Port Enable Override Setting the Default GatewayTrap Table Screen Exiting the Configuration ScreenExiting the Trap Table Screen 1 Configuring the Trap TableSnmp Tools Screen Snmp Tools ScreenLets you retrieve MIB objects using Snmp protocol Getting Individual OIDs Setting an OIDGetting the Next OID Walking Through OIDs Viewing Multiple OIDsCycling Through OIDs Stepping Through OIDsExiting the Snmp Tools Screen Device Statistics Screen Device Statistics ScreenDisplays the number of errors due to misaligned packets Module Number Sequence Selecting the Appropriate Module/PortUsing the Disable Port Command Using the Enable Port CommandExiting the Device Statistics Screen Epim Specifications Appendix a Epim SpecificationsEPIM-100TX EPIM-100FX Appendix B Image File Download Using Oids Setting UP a Unix Workstation AS a Tftp Server Standard Local Download Table B-1 OIDs and Settings Numerics IndexIndex-2 Power Supply Cord