Cabletron Systems SEHI100TX manual Cabletron SYSTEMS, INC. Program License Agreement

Page 4

Notice

CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT

IMPORTANT: Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron software program (the “Program”) contained in this package. The Program may be contained in firmware, chips or other media. BY UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.

CABLETRON SOFTWARE PROGRAM LICENSE

1.LICENSE. You have the right to use only the one (1) copy of the Program provided in this package subject to the terms and conditions of this License Agreement.

You may not copy, reproduce or transmit any part of the Program except as permitted by the Copyright Act of the United States or as authorized in writing by Cabletron.

2.OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program.

3.APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and venue of the New Hampshire courts.

EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY

1.EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its documentation and media).

CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY CABLETRON IN WRITING, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.

2.NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.

SEHI100TX User’s Guide

iii

Image 4
Contents Intelligent Stackable HUB USER’S Guide SEHI100TX User’s Guide FCC Notice Cabletron SYSTEMS, INC. Program License Agreement United States Government Restricted Rights Contents Contents SEHI100TX User’s Guide Vii Using this Manual Chapter IntroductionDocument Conventions Following conventions are used throughout this documentGetting Help Related ManualsChapter Sehi Features and Options Sehi OverviewSehi Features Sehi Features and OptionsStackable Capabilities Remote Network Management Rack Mounting CapabilitiesOptional 100BASE-TX and 100BASE-FX EPIMs Cable Specifications Chapter Installation Requirements SpecificationsHubSTACK Interconnect Cable Requirements UTP Cable Specifications Multimode Specifications for the EPIM-100FX Network Cable Lengths Network Port Specifications COM Port RequirementsPower Supply Requirements Operating SpecificationsEnvironmental Requirements Physical Specifications Agency ApprovalsChapter Installation Unpacking the SehiPRE-INSTALLATION Checkout Nvram Switch LocationTabletop or Shelf Installation SEHI100TX-22Rackmount Installation Screws Strain-Relief BracketRackmount Installation Installing the Sehi in the Rack Powering UP and Stacking the Sehi Repeat steps 3 through 6 until all SEH hubs are connected Installing the EPIM-100TX or the EPIM-100FX Install an EPIM-100TX or an EPIM-100FX as followsConnecting the Sehi to the Network Chapter Connecting to the NetworkConnecting to Network Ports Connecting a UTP Segment to an EPIM-100TX Sehi Network PortsPosition X crossed over RX+ TX+ Position = Not crossed over Connecting a Fiber Segment to the EPIM-100FX EPIM-100FX PortTesting the Installation Chapter Troubleshooting Installation TestUsing Lanview Using Lanview Using the Reset Button Epim 1 RCV LEDSetting the Nvram Switch Chapter Local Management Local Management Keyboard Conventions Keyboard Conventions FunctionManagement Terminal Setup Console Cable Configuration Management Terminal Setup Parameters Accessing Local Management Sehi Local ManagementFeature Selection Screen Feature Selection ScreenCommunity Name Table Screen Community Name Table ScreenEditing the Community Name Field Configuration Screen ConfigurationDisplays the IP address of the Sehi Setting the IP Address Setting the Subnet MaskSetting the Default Gateway Using the Port Enable OverrideExiting the Configuration Screen Trap Table Screen1 Configuring the Trap Table Exiting the Trap Table ScreenSnmp Tools Screen Snmp Tools ScreenLets you retrieve MIB objects using Snmp protocol Getting Individual OIDs Setting an OIDGetting the Next OID Viewing Multiple OIDs Walking Through OIDsCycling Through OIDs Stepping Through OIDsExiting the Snmp Tools Screen Device Statistics Screen Device Statistics ScreenDisplays the number of errors due to misaligned packets Selecting the Appropriate Module/Port Module Number SequenceUsing the Disable Port Command Using the Enable Port CommandExiting the Device Statistics Screen Epim Specifications Appendix a Epim SpecificationsEPIM-100TX EPIM-100FX Appendix B Image File Download Using Oids Setting UP a Unix Workstation AS a Tftp Server Standard Local Download Table B-1 OIDs and Settings Index NumericsIndex-2 Power Supply Cord