Cabletron Systems SEHI100TX manual Using the Enable Port Command, Using the Disable Port Command

Page 65

Chapter 7: Local Management

7.9.2Using the ENABLE PORT Command

The ENABLE PORT command lets the user enable the selected port. The user must ﬁrst use the PORT command to select the desired port.

Use the following steps to set the PORT ENABLE command:

1.Use the arrow keys to highlight the ENABLE PORT command at the bottom of the screen.

2.Press ENTER. The corresponding port is enabled and the Port Admin Status field is updated.

7.9.3Using the DISABLE PORT Command

The DISABLE PORT command lets the user disable the port selected in the PORT command. The user must ﬁrst use the PORT command to select the desired port.

Use the following steps to set the DISABLE PORT command:

1.Use the arrow keys to highlight the DISABLE PORT command at the bottom of the screen.

2.Press ENTER. The corresponding port is enabled and the Port Admin Status field is updated.

7.9.4Exiting the Device Statistics Screen

Use the following steps to exit the Device Statistics screen and return to the Feature Selection screen:

1.Use the arrow keys to highlight the RETURN command at the bottom of the screen.

2.Press ENTER. The Feature Selection screen appears.

7-24	SEHI100TX User’s Guide

Image 65

Contents Intelligent Stackable HUB USER’S Guide SEHI100TX User’s Guide FCC Notice Cabletron SYSTEMS, INC. Program License Agreement United States Government Restricted Rights Contents Contents SEHI100TX User’s Guide Vii Chapter Introduction Using this ManualFollowing conventions are used throughout this document Document ConventionsRelated Manuals Getting HelpSehi Overview Chapter Sehi Features and OptionsSehi Features and Options Sehi FeaturesStackable Capabilities Optional 100BASE-TX and 100BASE-FX EPIMs Rack Mounting CapabilitiesRemote Network Management HubSTACK Interconnect Cable Requirements Chapter Installation Requirements SpecificationsCable Specifications UTP Cable Speciﬁcations Multimode Speciﬁcations for the EPIM-100FX Network Cable Lengths COM Port Requirements Network Port SpecificationsEnvironmental Requirements Operating SpecificationsPower Supply Requirements Agency Approvals Physical SpecificationsUnpacking the Sehi Chapter InstallationNvram Switch Location PRE-INSTALLATION CheckoutSEHI100TX-22 Tabletop or Shelf InstallationScrews Strain-Relief Bracket Rackmount InstallationRackmount Installation Installing the Sehi in the Rack Powering UP and Stacking the Sehi Repeat steps 3 through 6 until all SEH hubs are connected Install an EPIM-100TX or an EPIM-100FX as follows Installing the EPIM-100TX or the EPIM-100FXConnecting to Network Ports Chapter Connecting to the NetworkConnecting the Sehi to the Network Sehi Network Ports Connecting a UTP Segment to an EPIM-100TXPosition X crossed over RX+ TX+ Position = Not crossed over EPIM-100FX Port Connecting a Fiber Segment to the EPIM-100FXTesting the Installation Installation Test Chapter TroubleshootingUsing Lanview Using Lanview Epim 1 RCV LED Using the Reset ButtonSetting the Nvram Switch Chapter Local Management Keyboard Conventions Function Local Management Keyboard ConventionsManagement Terminal Setup Console Cable Conﬁguration Management Terminal Setup Parameters Sehi Local Management Accessing Local ManagementFeature Selection Screen Feature Selection ScreenCommunity Name Table Screen Community Name Table ScreenEditing the Community Name Field Configuration Configuration ScreenDisplays the IP address of the Sehi Setting the Subnet Mask Setting the IP AddressUsing the Port Enable Override Setting the Default GatewayTrap Table Screen Exiting the Conﬁguration ScreenExiting the Trap Table Screen 1 Conﬁguring the Trap TableSnmp Tools Screen Snmp Tools ScreenLets you retrieve MIB objects using Snmp protocol Getting the Next OID Setting an OIDGetting Individual OIDs Walking Through OIDs Viewing Multiple OIDsExiting the Snmp Tools Screen Stepping Through OIDsCycling Through OIDs Device Statistics Screen Device Statistics ScreenDisplays the number of errors due to misaligned packets Module Number Sequence Selecting the Appropriate Module/PortExiting the Device Statistics Screen Using the Enable Port CommandUsing the Disable Port Command EPIM-100TX Appendix a Epim SpecificationsEpim Specifications EPIM-100FX Appendix B Image File Download Using Oids Setting UP a Unix Workstation AS a Tftp Server Standard Local Download Table B-1 OIDs and Settings Numerics IndexIndex-2 Power Supply Cord