Cabletron Systems BRIM-F6 manual Installing an Hsim in a Standalone Hub, Installing the HSIM-F6

Page 23

Installing an HSIM

Standoff Screws

HSIM Connector

HSIM

A

B

A
P	B
	S

Pins

Faceplate Mounting Screws

Standoffs

225705

Figure 2-4 Installing the HSIM-F6

2.3.2Installing an HSIM in a Standalone Hub

To install an HSIM-F6 into a standalone hub (e.g. 2E42-27), perform the following steps:

1.Power down the hub and remove the power cord.

2.Note the ports that have cables attached to them. Then disconnect those cables from the ports.

To install the HSIM-F6 in a standalone hub the device MUST be powered down.

Ensure that you remove the power cord and ONLY the screws required to remove the chassis cover. Failure to comply could result in an electric shock hazard.

HSIM-F6 User’s Guide

2-7

Image 23

Contents HSIM-F6 Page HSIM-F6 User’s Guide DOC Notice Cabletron Software Program License HSIM-F6 User’s Guide Declaration of Conformity HSIM-F6 User’s Guide Contents Viii HSIM-F6 User’s Guide Chapter Introduction Document Conventions Using this ManualYour email address Getting HelpOverview FeaturesSpecifications Cabletron Systems Fddi Technology Guide Related DocumentationUnpacking the Hsim Chapter InstallationPress the Fpim connector into the Hsim pins Installing FPIMsInstalling FPIMs Installing an Hsim in an Interface Module Installing AN HsimInstalling an Hsim HSIM-F6 User’s Guide Installing the HSIM-F6 Installing an Hsim in a Standalone HubHSIM-F6 User’s Guide Chapter Local Management Key Function Local Management Keyboard ConventionsKeyboard Conventions Exiting Local Management Screens Selecting Local Management Menu Screen ItemsNavigating Local Management Screens HSIM-F6 Setup ScreenHSIM-F6 Setup Screen HSIM-F6 Conﬁguration HSIM-F6 Statistics Screen HSIM-F6 Statistics ScreenMIB-II Statistics Screen HSIM-F6 Statistics Screen FieldsMIB-II Interface Statistics Screen Fields HSIM-F6 Fddi Ring Statistics Screen Ring Statistics ScreenHSIM-F6 Fddi Ring Statistics Screen Fields MAC Configuration Primary Out Port a Isolated Both port a and port B are isolated from the ring Master Port Count 11 The Ring Map Conﬁguration Screen Ring MAP Configuration ScreenRing Map Conﬁguration Screen Fields Adjusting the Scroll Number n Ring Map Conﬁguration Screen Commands12 The Ring Map Node Information Screen Node Information ScreenNode Information Screen Fields 13 The HSIM-F6 Conﬁguration Screen HSIM-F6 Configuration ScreenHSIM-F6 Conﬁguration Screen Fields 14 The Fddi Full Duplex Conﬁguration Screen Full Duplex Configuration ScreenFull Duplex Fddi Full Duplex Conﬁguration Screen Fields 3 Conﬁguring the HSIM-F6 for Full Duplex Operation FDDI/ETHERNET Translation Configuration Screen Ethernet Ethernet Snap Fddi Translation Conﬁguration Screen FieldsDefault setting for the Novell Fddi 802.2 ﬁeld is Ethernet Enabled Setting Frame Translation TypesSetting the Interpret 802.3 Length Field to Enabled Setting the Frame Translation Types to the Default ValuesHSIM-F6 User’s Guide Color Deﬁnition HSIM-F6 Transmit and Receive LEDsPort a and Port B LED States and Deﬁnitions Color DefinitionA, B, P, S LED Deﬁnitions HSIM-F6 LED State DefinitionsHSIM-F6 User’s Guide HSIM-F6 LED State Deﬁnitions HSIM-F6 User’s Guide Multimode Receiver Speciﬁcations Fiber Optic InterfaceMultimode Speciﬁcations Multimode Transmitter SpeciﬁcationsSingle Mode Receiver Speciﬁcations Single Mode SpeciﬁcationsMultimode Receiver Signal Detect Speciﬁcations Single Mode Transmitter SpeciﬁcationsSingle Mode Receiver Signal Detect Single Mode Receiver Signal Detect SpeciﬁcationsUTP Transmitter Speciﬁcations Unshielded Twisted Pair UTP SpecificationsUTP Receiver Signal Detect UTP Receiver Signal DetectSTP Transmitter Speciﬁcations Shielded Twisted Pair STP Transmitter Specifications10 STP Receiver Signal Detect Speciﬁcations STP Receiver Signal DetectMultimode Fiber Optic Cable Length Cable SpecificationsSingle Mode Fiber Optic Cable Length Twisted Pair Cable Length Twisted Pair Pinout ConfigurationHSIM-F6 User’s Guide Worst Typical Parameter Typical Value Case Budget Table A-1 FPIM-00 and FPIM-01 SpecificationsFPIM-00 and FPIM-01 Figure A-2 FPIM-02 and FPIM-04 Pinouts FPIM-02 and FPIM-04Parameter Typical Value Minimum Maximum Table A-2 FPIM-05 and FPIM-07 SpecificationsFPIM-05 and FPIM-07 HSIM-F6 User’s Guide

Related manuals

Manual 43 pages 29.03 Kb