Cabletron Systems BRIM-F6 manual HSIM-F6 User’s Guide

Page 3

Only qualiﬁed personnel should perform installation procedures.

NOTICE

Cabletron Systems reserves the right to make changes in speciﬁcations and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.

The hardware, ﬁrmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

Copyright 1997 by Cabletron Systems, Inc., P.O. Box 5005, Rochester, NH 03866-5005 All Rights Reserved

Printed in the United States of America

Order Number: 9032091-03 September 1997

Cabletron Systems and LANVIEW are registered trademarks, HSIM and FPIM are trademarks of Cabletron Systems, Inc.

All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies.

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not installed in accordance with the operator’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense.

WARNING: Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Printed on

Recycled Paper

HSIM-F6 User’s Guide

i

Image 3

Contents HSIM-F6 Page HSIM-F6 User’s Guide DOC Notice Cabletron Software Program License HSIM-F6 User’s Guide Declaration of Conformity HSIM-F6 User’s Guide Contents Viii HSIM-F6 User’s Guide Chapter Introduction Document Conventions Using this ManualYour email address Getting HelpOverview FeaturesSpecifications Cabletron Systems Fddi Technology Guide Related DocumentationUnpacking the Hsim Chapter InstallationPress the Fpim connector into the Hsim pins Installing FPIMsInstalling FPIMs Installing an Hsim in an Interface Module Installing AN HsimInstalling an Hsim HSIM-F6 User’s Guide Installing the HSIM-F6 Installing an Hsim in a Standalone HubHSIM-F6 User’s Guide Chapter Local Management Local Management Keyboard Conventions Keyboard ConventionsKey Function Exiting Local Management Screens Selecting Local Management Menu Screen ItemsNavigating Local Management Screens HSIM-F6 Setup ScreenHSIM-F6 Setup Screen HSIM-F6 Conﬁguration HSIM-F6 Statistics Screen HSIM-F6 Statistics ScreenMIB-II Statistics Screen HSIM-F6 Statistics Screen FieldsMIB-II Interface Statistics Screen Fields HSIM-F6 Fddi Ring Statistics Screen Ring Statistics ScreenHSIM-F6 Fddi Ring Statistics Screen Fields MAC Configuration Primary Out Port a Isolated Both port a and port B are isolated from the ring Master Port Count 11 The Ring Map Conﬁguration Screen Ring MAP Configuration ScreenRing Map Conﬁguration Screen Fields Adjusting the Scroll Number n Ring Map Conﬁguration Screen Commands12 The Ring Map Node Information Screen Node Information ScreenNode Information Screen Fields 13 The HSIM-F6 Conﬁguration Screen HSIM-F6 Configuration ScreenHSIM-F6 Conﬁguration Screen Fields 14 The Fddi Full Duplex Conﬁguration Screen Full Duplex Configuration ScreenFull Duplex Fddi Full Duplex Conﬁguration Screen Fields 3 Conﬁguring the HSIM-F6 for Full Duplex Operation FDDI/ETHERNET Translation Configuration Screen Ethernet Ethernet Snap Fddi Translation Conﬁguration Screen FieldsDefault setting for the Novell Fddi 802.2 ﬁeld is Ethernet Enabled Setting Frame Translation TypesSetting the Interpret 802.3 Length Field to Enabled Setting the Frame Translation Types to the Default ValuesHSIM-F6 User’s Guide Color Deﬁnition HSIM-F6 Transmit and Receive LEDsPort a and Port B LED States and Deﬁnitions Color DefinitionA, B, P, S LED Deﬁnitions HSIM-F6 LED State DefinitionsHSIM-F6 User’s Guide HSIM-F6 LED State Deﬁnitions HSIM-F6 User’s Guide Multimode Receiver Speciﬁcations Fiber Optic InterfaceMultimode Speciﬁcations Multimode Transmitter SpeciﬁcationsSingle Mode Receiver Speciﬁcations Single Mode SpeciﬁcationsMultimode Receiver Signal Detect Speciﬁcations Single Mode Transmitter SpeciﬁcationsSingle Mode Receiver Signal Detect Single Mode Receiver Signal Detect SpeciﬁcationsUTP Transmitter Speciﬁcations Unshielded Twisted Pair UTP SpecificationsUTP Receiver Signal Detect UTP Receiver Signal DetectSTP Transmitter Speciﬁcations Shielded Twisted Pair STP Transmitter Specifications10 STP Receiver Signal Detect Speciﬁcations STP Receiver Signal DetectCable Specifications Single Mode Fiber Optic Cable LengthMultimode Fiber Optic Cable Length Twisted Pair Cable Length Twisted Pair Pinout ConfigurationHSIM-F6 User’s Guide Table A-1 FPIM-00 and FPIM-01 Specifications FPIM-00 and FPIM-01Worst Typical Parameter Typical Value Case Budget Figure A-2 FPIM-02 and FPIM-04 Pinouts FPIM-02 and FPIM-04Table A-2 FPIM-05 and FPIM-07 Specifications FPIM-05 and FPIM-07Parameter Typical Value Minimum Maximum HSIM-F6 User’s Guide

Related manuals

Manual 43 pages 29.03 Kb