Cabletron Systems BRIM-F6 manual HSIM-F6 Fddi Ring Statistics Screen Fields

Page 35

The Ring Statistics Screen

3.6.1HSIM-F6 FDDI Ring Statistics Screen Fields

The HSIM-F6 FDDI Ring Statistics screen allows the user to monitor the current HSIM-F6 operational status.

The following list describes the Ring Statistics screen fields:

RING STATE

Displays the current ring state. The possible ring states are as follows:

Ring-Op - The ring is functioning correctly.

Isolated - The HSIM-F6 is not attached to the ring.

Non-Op - The HSIM-F6 is attempting to enter the ring.

• Detect -

The claim (beacon) process of the FDDI ring

 

protocol has exceeded one second. There may be a

 

problem.

Non-Op-Dup - The ring failed to complete the claim (beacon) process. This usually indicates a duplicate FDDI address.

Ring-Op-Dup - The ring is operational, but a duplicate FDDI address may be present somewhere on the network.

Directed - The claim (beacon) process did not complete within ten seconds. The HSIM-F6 is sending directed beacons to indicate a problem.

• Trace -

A problem has been detected with the HSIM-F6 or

 

the nearest active upstream neighbor (NAUN). A

 

trace is being sent to notify the nearest active

 

upstream neighbor of the problem.

RING-OP COUNT

The Ring-Op Count keeps track of the number of times the FDDI ring has initialized since the last time the HSIM-F6 (or host device in which it resides) was reset. If this number grows steadily over a brief period of time, it signifies the ring is unstable.

HSIM-F6 User’s Guide

3-11

Image 35
Contents HSIM-F6 Page HSIM-F6 User’s Guide DOC Notice Cabletron Software Program License HSIM-F6 User’s Guide Declaration of Conformity HSIM-F6 User’s Guide Contents Viii HSIM-F6 User’s Guide Chapter Introduction Document Conventions Using this ManualYour email address Getting HelpOverview FeaturesSpecifications Cabletron Systems Fddi Technology Guide Related DocumentationUnpacking the Hsim Chapter InstallationPress the Fpim connector into the Hsim pins Installing FPIMsInstalling FPIMs Installing an Hsim in an Interface Module Installing AN HsimInstalling an Hsim HSIM-F6 User’s Guide Installing the HSIM-F6 Installing an Hsim in a Standalone HubHSIM-F6 User’s Guide Chapter Local Management Key Function Local Management Keyboard ConventionsKeyboard Conventions Exiting Local Management Screens Selecting Local Management Menu Screen ItemsNavigating Local Management Screens HSIM-F6 Setup ScreenHSIM-F6 Setup Screen HSIM-F6 Configuration HSIM-F6 Statistics Screen HSIM-F6 Statistics ScreenMIB-II Statistics Screen HSIM-F6 Statistics Screen FieldsMIB-II Interface Statistics Screen Fields HSIM-F6 Fddi Ring Statistics Screen Ring Statistics ScreenHSIM-F6 Fddi Ring Statistics Screen Fields MAC Configuration Primary Out Port a Isolated Both port a and port B are isolated from the ring Master Port Count 11 The Ring Map Configuration Screen Ring MAP Configuration ScreenRing Map Configuration Screen Fields Adjusting the Scroll Number n Ring Map Configuration Screen Commands12 The Ring Map Node Information Screen Node Information ScreenNode Information Screen Fields 13 The HSIM-F6 Configuration Screen HSIM-F6 Configuration ScreenHSIM-F6 Configuration Screen Fields 14 The Fddi Full Duplex Configuration Screen Full Duplex Configuration ScreenFull Duplex Fddi Full Duplex Configuration Screen Fields 3 Configuring the HSIM-F6 for Full Duplex Operation FDDI/ETHERNET Translation Configuration Screen Ethernet Ethernet Snap Fddi Translation Configuration Screen FieldsDefault setting for the Novell Fddi 802.2 field is Ethernet Enabled Setting Frame Translation TypesSetting the Interpret 802.3 Length Field to Enabled Setting the Frame Translation Types to the Default ValuesHSIM-F6 User’s Guide Color Definition HSIM-F6 Transmit and Receive LEDsPort a and Port B LED States and Definitions Color DefinitionA, B, P, S LED Definitions HSIM-F6 LED State DefinitionsHSIM-F6 User’s Guide HSIM-F6 LED State Definitions HSIM-F6 User’s Guide Multimode Receiver Specifications Fiber Optic InterfaceMultimode Specifications Multimode Transmitter SpecificationsSingle Mode Receiver Specifications Single Mode SpecificationsMultimode Receiver Signal Detect Specifications Single Mode Transmitter SpecificationsSingle Mode Receiver Signal Detect Single Mode Receiver Signal Detect SpecificationsUTP Transmitter Specifications Unshielded Twisted Pair UTP SpecificationsUTP Receiver Signal Detect UTP Receiver Signal DetectSTP Transmitter Specifications Shielded Twisted Pair STP Transmitter Specifications10 STP Receiver Signal Detect Specifications STP Receiver Signal DetectMultimode Fiber Optic Cable Length Cable SpecificationsSingle Mode Fiber Optic Cable Length Twisted Pair Cable Length Twisted Pair Pinout ConfigurationHSIM-F6 User’s Guide Worst Typical Parameter Typical Value Case Budget Table A-1 FPIM-00 and FPIM-01 SpecificationsFPIM-00 and FPIM-01 Figure A-2 FPIM-02 and FPIM-04 Pinouts FPIM-02 and FPIM-04Parameter Typical Value Minimum Maximum Table A-2 FPIM-05 and FPIM-07 SpecificationsFPIM-05 and FPIM-07 HSIM-F6 User’s Guide
Related manuals
Manual 43 pages 29.03 Kb