Cabletron Systems BRIM-F6 manual Installing AN Hsim, Installing an Hsim in an Interface Module

Page 20

Chapter 2: Installation

5.Press down firmly on the FPIM until the pins slide all the way into the HSIM connector.

6.Secure the FPIM with the screws saved in step 2.

7.Secure the faceplate of the HSIM with the screws saved in step 3.

2.3INSTALLING AN HSIM

Only qualiﬁed personnel should install or service this unit.

You can install an HSIM in any Cabletron Systems device that supports HSIM technology (e.g., 2E42-27, 6E132-25). Refer to the release notes for the version of ﬁrmware running on the Cabletron Systems device to ensure that the HSIM-F6 is supported. The following subsections provide generic instructions for installing an HSIM-F6 in an interface module or in a standalone hub. Refer to your speciﬁc interface module or standalone hub documentation for exact HSIM slot and connector locations.

2.3.1Installing an HSIM in an Interface Module

!

CAUTION

The HSIM-F6 and the host module or standalone hub are sensitive to static discharges. Use an antistatic wrist strap and observe all static precautions during this procedure. Failure to do so could result in damage to the HSIM-F6, the host module or standalone hub.

To install an HSIM-F6 in an interface module that supports HSIM technology perform the following steps.

1.Note the ports of the interface module that have cables attached to them. Then disconnect those cables from the ports.

2.Attach the antistatic wrist strap (refer to the instructions outlined in the interface module User’s Guide).

3.Unlock the top and bottom plastic locking tabs of the module faceplate.

2-4	HSIM-F6 User’s Guide

Image 20

Contents HSIM-F6 Page HSIM-F6 User’s Guide DOC Notice Cabletron Software Program License HSIM-F6 User’s Guide Declaration of Conformity HSIM-F6 User’s Guide Contents Viii HSIM-F6 User’s Guide Chapter Introduction Using this Manual Document ConventionsGetting Help Your email addressFeatures OverviewSpecifications Related Documentation Cabletron Systems Fddi Technology GuideChapter Installation Unpacking the HsimInstalling FPIMs Press the Fpim connector into the Hsim pinsInstalling FPIMs Installing AN Hsim Installing an Hsim in an Interface ModuleInstalling an Hsim HSIM-F6 User’s Guide Installing an Hsim in a Standalone Hub Installing the HSIM-F6HSIM-F6 User’s Guide Chapter Local Management Key Function Local Management Keyboard ConventionsKeyboard Conventions Selecting Local Management Menu Screen Items Exiting Local Management ScreensHSIM-F6 Setup Screen Navigating Local Management ScreensHSIM-F6 Setup Screen HSIM-F6 Conﬁguration HSIM-F6 Statistics Screen HSIM-F6 Statistics ScreenHSIM-F6 Statistics Screen Fields MIB-II Statistics ScreenMIB-II Interface Statistics Screen Fields Ring Statistics Screen HSIM-F6 Fddi Ring Statistics ScreenHSIM-F6 Fddi Ring Statistics Screen Fields MAC Configuration Primary Out Port a Isolated Both port a and port B are isolated from the ring Master Port Count Ring MAP Configuration Screen 11 The Ring Map Conﬁguration ScreenRing Map Conﬁguration Screen Fields Ring Map Conﬁguration Screen Commands Adjusting the Scroll Number nNode Information Screen 12 The Ring Map Node Information ScreenNode Information Screen Fields HSIM-F6 Configuration Screen 13 The HSIM-F6 Conﬁguration ScreenHSIM-F6 Conﬁguration Screen Fields Full Duplex Configuration Screen 14 The Fddi Full Duplex Conﬁguration ScreenFull Duplex Fddi Full Duplex Conﬁguration Screen Fields 3 Conﬁguring the HSIM-F6 for Full Duplex Operation FDDI/ETHERNET Translation Configuration Screen Fddi Translation Conﬁguration Screen Fields Ethernet Ethernet SnapDefault setting for the Novell Fddi 802.2 ﬁeld is Ethernet Setting Frame Translation Types EnabledSetting the Frame Translation Types to the Default Values Setting the Interpret 802.3 Length Field to EnabledHSIM-F6 User’s Guide HSIM-F6 Transmit and Receive LEDs Color DeﬁnitionColor Definition Port a and Port B LED States and DeﬁnitionsHSIM-F6 LED State Definitions A, B, P, S LED DeﬁnitionsHSIM-F6 User’s Guide HSIM-F6 LED State Deﬁnitions HSIM-F6 User’s Guide Fiber Optic Interface Multimode SpeciﬁcationsMultimode Transmitter Speciﬁcations Multimode Receiver SpeciﬁcationsSingle Mode Speciﬁcations Multimode Receiver Signal Detect SpeciﬁcationsSingle Mode Transmitter Speciﬁcations Single Mode Receiver SpeciﬁcationsSingle Mode Receiver Signal Detect Speciﬁcations Single Mode Receiver Signal DetectUnshielded Twisted Pair UTP Specifications UTP Receiver Signal DetectUTP Receiver Signal Detect UTP Transmitter SpeciﬁcationsShielded Twisted Pair STP Transmitter Specifications 10 STP Receiver Signal Detect SpeciﬁcationsSTP Receiver Signal Detect STP Transmitter SpeciﬁcationsMultimode Fiber Optic Cable Length Cable SpecificationsSingle Mode Fiber Optic Cable Length Twisted Pair Pinout Configuration Twisted Pair Cable LengthHSIM-F6 User’s Guide Worst Typical Parameter Typical Value Case Budget Table A-1 FPIM-00 and FPIM-01 SpecificationsFPIM-00 and FPIM-01 FPIM-02 and FPIM-04 Figure A-2 FPIM-02 and FPIM-04 PinoutsParameter Typical Value Minimum Maximum Table A-2 FPIM-05 and FPIM-07 SpecificationsFPIM-05 and FPIM-07 HSIM-F6 User’s Guide

Related manuals

Manual 43 pages 29.03 Kb