Cabletron Systems 9A426-02 manual Related Manuals, Getting Help

Page 12

Introduction

Related Manuals

The manuals listed below should be used to supplement the procedures and technical data contained in this manual.

SmartSwitch 9000 Installation Guide

SmartSwitch 9000 9C300-1 Environmental Module User’s Guide

SmartSwitch 9000 9C214-1 AC Power Supply User’s Guide

INB Terminator Modules Installation Guide

SmartSwitch 9000 Local Management User’s Guide

SmartSwitch 9000 9A426-01/9A426-02 Module-Specific Local Management Appendix

Getting Help

For additional support related to this device or document, contact the Cabletron Systems Global Call Center:

Phone

(603) 332-9400

 

 

Internet mail

support@ctron.com

 

 

FTP

ctron.com (134.141.197.25)

Login

anonymous

Password

your email address

 

 

BBS

(603) 335-3358

Modem setting

8N1: 8 data bits, No parity, 1 stop bit

 

 

For additional information about Cabletron Systems or its products, visit the

World Wide Web site: http://www.cabletron.com/

For technical support, select Service and Support.

To send comments or suggestions concerning this document, contact the Cabletron Systems Technical Writing Department via the following email address: TechWriting@ctron.com

Make sure to include the document Part Number in the email message.

Before calling the Cabletron Systems Global Call Center, have the following information ready:

•Your Cabletron Systems service contract number

•A description of the failure

•A description of any action(s) already taken to resolve the problem (e.g., changing mode switches, rebooting the unit, etc.)

•The serial and revision numbers of all involved Cabletron Systems products in the network

•A description of your network environment (layout, cable type, etc.)

•Network load and frame size at the time of trouble (if known)

•The device history (i.e., have you returned the device before, is this a recurring problem, etc.)

•Any previous Return Material Authorization (RMA) numbers

1-4

Page 11 Page 13
Image 12
Page 11 Page 13
Contents SmartSwitch 9A426-02 User’s Guide Page Page FCC Notice Vcci NoticeDOC Notice Declaration of Conformity Page Contents Chapter Lanview LEDs Specifications CPUIntroduction Features Ietf Fddi MIBLanview LEDs Related Manuals Getting HelpUnpacking the Module Module’s Physical LayoutUser-Accessible Components on the Module’s Motherboard 9A426-02 Module’s two major circuit boardsLook-Up Engines Installing an Apim in the 9A426-02 Module Sram SIMMsAPIMs Unpacking an Apim Removing the 9A426-02 Module’s ATM-Port Retaining PlateATM-Port Retaining Plate Inserting an Apim into the 9A426-02 Module Removing the ATM-Port Retaining PlateAttaching the 9A426-02 Module’s ATM-Port Retaining Plate Attaching an Apim to a 9A426-02 ModuleUser-Accessible Components on the Module’s Daughterboard DIP Switch Switch Function Description Removing the Daughterboard from the Motherboard Securing SMB-1 Prom Installing the Module into the SmartSwitch 9000 Chassis Preparing and Installing the 9A426-02 Module 11. Installing the 9A426-02 Module Reset Switch 12. The Reset SwitchOperation Front Panel Backplane LAN Emulation System Management BusesSMB-1 Bus System Diagnostic Controller DC/DC ConverterINB Network Interface Block SMB-10 BusFddi Network Interface Block ATM Network Interface BlockSecureFast Virtual Networking I960 Core Lanview LEDs Status of the INB Receive LED is listed in Table Status of the FNB Receive LED is listed in Table Status of the ATM Transmit LED is listed in Table Status of the Apim Link LNK LED is listed in Table Lanview LEDs Power Technical SpecificationsMemory Address Table SizeSafety ServiceStandards Dimensions WeightPhysical EnvironmentSpecifications
Top Page Image Contents