Cabletron Systems 9A426-02 manual Installing the Module into the SmartSwitch 9000 Chassis

Page 27

Preparing and Installing the 9A426-02 Module

BOOT PROM

The 9A426-02 Module is shipped with a BOOT PROM. The BOOT PROM is located on the underside of the module’s daughterboard as shown in Figure 2-10.

To upgrade the BOOT PROM, install the BOOT PROM Upgrade Kit. Installation instructions are included in the upgrade kit.

FLASH SIMM

The 9A426-02 Module is shipped with a 4Mb FLASH SIMM. The FLASH SIMM’s socket is located on the underside of the module’s daughterboard as shown in Figure 2-10.

To upgrade the FLASH SIMM, refer to the installation instructions included in the FLASH SIMM Upgrade Kit.

DRAM SIMM

The 9A426-02 Module is shipped with 16 Mb of DRAM (on the module’s motherboard). However if additional DRAM is desired, you can install a DRAM SIMM in the socket on the underside of the module’s daughterboard as shown in Figure 2-10.

To install a DRAM SIMM, refer to the installation instructions included in the DRAM SIMM Upgrade Kit.

Installing the Module into the SmartSwitch 9000 Chassis

To install the 9A426-02 Module into the SmartSwitch 9000 Chassis, follow the steps below:

NOTE

To insure proper data transmission from the 9A426-02 Module to the INB on the SmartSwitch 9000 backplane, two INB Terminator Modules must be installed on the rear of the SmartSwitch 9000 chassis. Refer to the INB Terminator Module Installation Guide for information and installation procedure.

1.Remove the blank panel covering the slot in which the module is being installed. If you are only installing one module, make sure the chassis’ other module slots are covered. This action ensures proper airflow and cooling.

2-15

Page 26 Page 28
Image 27
Page 26 Page 28
Contents SmartSwitch 9A426-02 User’s Guide Page Page FCC Notice Vcci NoticeDOC Notice Declaration of Conformity Page Contents CPU Chapter Lanview LEDs SpecificationsIntroduction Ietf Fddi MIB FeaturesLanview LEDs Getting Help Related ManualsModule’s Physical Layout Unpacking the Module9A426-02 Module’s two major circuit boards User-Accessible Components on the Module’s MotherboardLook-Up Engines Installing an Apim in the 9A426-02 Module Sram SIMMsAPIMs Removing the 9A426-02 Module’s ATM-Port Retaining Plate Unpacking an ApimATM-Port Retaining Plate Removing the ATM-Port Retaining Plate Inserting an Apim into the 9A426-02 ModuleAttaching an Apim to a 9A426-02 Module Attaching the 9A426-02 Module’s ATM-Port Retaining PlateUser-Accessible Components on the Module’s Daughterboard DIP Switch Switch Function Description Removing the Daughterboard from the Motherboard Securing SMB-1 Prom Installing the Module into the SmartSwitch 9000 Chassis Preparing and Installing the 9A426-02 Module 11. Installing the 9A426-02 Module 12. The Reset Switch Reset SwitchOperation Front Panel Backplane LAN Emulation System Management BusesSMB-1 Bus SMB-10 Bus System Diagnostic ControllerDC/DC Converter INB Network Interface BlockFddi Network Interface Block ATM Network Interface BlockSecureFast Virtual Networking I960 Core Lanview LEDs Status of the INB Receive LED is listed in Table Status of the FNB Receive LED is listed in Table Status of the ATM Transmit LED is listed in Table Status of the Apim Link LNK LED is listed in Table Lanview LEDs Address Table Size PowerTechnical Specifications MemorySafety ServiceStandards Environment DimensionsWeight PhysicalSpecifications
Top Page Image Contents