Cabletron Systems 9A426-02 manual Switch Function Description

Page 23

Preparing and Installing the 9A426-02 Module

Table 2-1. Function of DIP Switch

!

CAUTION

Switch

Function

Description

 

 

 

 

 

When toggled, this switch clears user-entered

 

Clear

passwords stored in NVRAM, and restores the

8

default passwords. Once the passwords are

Password 1

 

reset, you can use the defaults or enter new

 

 

 

 

passwords.

 

 

 

 

 

The module uses NVRAM to store user

 

 

entered parameters such as IP addresses,

 

Clear

device name, etc. To reset these parameters to

7

the factory defaults, toggle this switch. Once

NVRAM 2

reset you can use the defaults or enter new

 

 

 

parameters which are stored in NVRAM when

 

 

the module is powered down, and remain

 

 

there until the switch is toggled again.

 

 

 

 

 

Toggling this switch after pulling the board out

 

 

of the SmartSwitch 9000, clears download

 

Force BootP

information from NVRAM and forces image

6

files to be downloaded from the station

Download

 

connected to the EPIM on the Environmental

 

 

 

 

Module configured to act as that module’s

 

 

BOOTP server.

 

 

 

5

Reserved

For Factory Use Only

 

 

 

4

Reserved

For Factory Use Only

 

 

 

3

Reserved

For Factory Use Only

 

 

 

2

Reserved

For Factory Use Only

 

 

 

1

Reserved

For Factory Use Only

 

 

 

1Do not toggle Switch 8 unless you intend to reset the user configured passwords to their factory default settings.

2Do not toggle Switch 7 unless you intend to reset the user parameters to the factory default settings.

2-11

Page 22 Page 24
Image 23
Page 22 Page 24
Contents SmartSwitch 9A426-02 User’s Guide Page Page DOC Notice FCC NoticeVcci Notice Declaration of Conformity Page Contents CPU Chapter Lanview LEDs SpecificationsIntroduction Ietf Fddi MIB FeaturesLanview LEDs Getting Help Related ManualsModule’s Physical Layout Unpacking the Module9A426-02 Module’s two major circuit boards User-Accessible Components on the Module’s MotherboardLook-Up Engines APIMs Installing an Apim in the 9A426-02 ModuleSram SIMMs Removing the 9A426-02 Module’s ATM-Port Retaining Plate Unpacking an ApimATM-Port Retaining Plate Removing the ATM-Port Retaining Plate Inserting an Apim into the 9A426-02 ModuleAttaching an Apim to a 9A426-02 Module Attaching the 9A426-02 Module’s ATM-Port Retaining PlateUser-Accessible Components on the Module’s Daughterboard DIP Switch Switch Function Description Removing the Daughterboard from the Motherboard Securing SMB-1 Prom Installing the Module into the SmartSwitch 9000 Chassis Preparing and Installing the 9A426-02 Module 11. Installing the 9A426-02 Module 12. The Reset Switch Reset SwitchOperation Front Panel Backplane SMB-1 Bus LAN EmulationSystem Management Buses SMB-10 Bus System Diagnostic ControllerDC/DC Converter INB Network Interface BlockSecureFast Virtual Networking Fddi Network Interface BlockATM Network Interface Block I960 Core Lanview LEDs Status of the INB Receive LED is listed in Table Status of the FNB Receive LED is listed in Table Status of the ATM Transmit LED is listed in Table Status of the Apim Link LNK LED is listed in Table Lanview LEDs Address Table Size PowerTechnical Specifications MemoryStandards SafetyService Environment DimensionsWeight PhysicalSpecifications
Top Page Image Contents