Extron electronic IPL T S2, IPL T S4, IPL T S1, IPL T S6 setup guide Rear Panel

Page 15

Rear Panel

The rear panel has connectors for power, control, signal input, and signal output, and indicators as described below.

A Power receptacle — connects the supplied

12 VDC power supply

B LAN Activity LED — yellow LED blinks when sending and receiving data

C LAN receptacle — RJ-45 receptacle for network connection

D Link LED — green when connected to a network

E Captive screw connectors

— 3.5 mm, 5-pole, captive screw connectors for serial port connections

F COM1 — 9-pin D connector for serial port 1

G COM2 — 9-pin D connector for serial port 2

H COM3 — 9-pin D connector for serial port 3

I COM4 — 9-pin D connector for serial port 4

J UID # — The unique User ID Number (MAC address) of the unit

(ex: 00-05-A6-00-00-01)

10IPL T S1

00-05-A6-00-00-01

12V

0.5 A

COM1LAN

1

6

2

3

4

10 IPL T S2			6
00-05-A6-00-00-02			COM1

POWER	LAN		COM2

12V
		COM1	COM2
.5A MAX

			TX RX		TX RX
1	2	3	4	5	7

	10	6	8
	IPL T S4
00-05-A6-00-00-04		COM1	COM3
POWER	LAN		COM4
POWER		COM2
12V		COM2
12V

.5A MAX

1

2

3

4

7

9

10 IPL T S6				6
00-05-A6-00-00-06				COM1
00-05-A6-00-00-06
POWER	LAN			COM2
POWER
12V
12V		COM3	COM4 COM5	COM6
.5A MAX		COM3	COM4 COM5	COM6
.5A MAX
		TX RX	TX RX TX RX	TX RX

1

2

3

4

5

7

IPL T S Series Interfaces • Hardware Setup

2-3

Image 15

Contents Interfaces IPL T S SeriesSafety Instructions English Precautions安全须知中文 Page Table of Contents Table of Contents, cont’d IPL T S Series Interfaces OneIntroduction About this ManualIPL T S Series Products IPL T S1 Introduction, cont’d Global Configurator Click the Download GCSWxxxxx.exe button Installing Global ConfiguratorClick the Global Configurator icon System requirementsIntroduction, cont’d Two Front Panel Hardware SetupRear Panel Local Area Network LAN Connection Hardware Setup, cont’d Power ConnectionSerial Device Connection RJ-45 Connector Straight-through CableHardware Setup, cont’d Pin D connectorCaptive screw connector IPL T S6 Hardware Setup, cont’d Three Click the Add Driver Subscriptions button Software SetupCreating a Global Configurator Project File Step one download device driversClick the right arrow Subscribe button Step two create a new project Software Setup, cont’dIPL T S Series Interfaces Software Setup Step three add a device Click Edit Add DeviceClick Make this device a GlobalViewer Host if desired Click Auto Configure IP Address Step four define the location of the new device Step five save the new Global Configurator file Software Setup, cont’d Configuring a New Device Step six configure contactsClick Edit Contact Manager Click Edit Email Manager Step seven configure e-mailDriver Configuration tab opens Step eight assign device driversClick Add Driver Step nine set scheduled actions and e-mail deliveries Click Apply Action IPL T S Series Interfaces Software Setup Click Apply Email/Contacts Step ten set monitored conditions Click Apply Condition Click ConditionsStep eleven build the Global Configurator file Building and Uploading a GC FileApply Email/Contacts Step twelve upload the Global Configurator file Step thirteen change device settings if desired Click Tools Change Device SettingsSet Mail Server..., Set Gateway..., Set Subnet Mask..., etc Step fourteen launch GlobalViewer Software Setup, cont’d Launching the GlobalViewer InterfaceIPL T S Series Interfaces Software Setup USA, Canada, South America Japan Central America Extron’s WarrantyExtron USA East Setup Guide Checklist