Extron electronic IPL T S2, IPL T S4, IPL T S1, IPL T S6 setup guide 安全须知 中文

Page 3

安全须知 中文

这个符号提示用户该设备用户手册中 有重要的操作和维护说明。

这个符号警告用户该设备机壳内有暴

露的危险电压,有触电危险。

注意

阅读说明书 用 户 使 用 该 设 备 前 必 须 阅 读 并 理

解 所 有 安 全 和 使 用 说 明 。

保存说明书 用户应保存安全说明书以备将来使

用。

遵守警告 用户应遵守产品和用户指南上的所有安

全和操作说明。

避免追加 不要使用该产品厂商没有推荐的工具或 追加设备,以避免危险。

警告

电源 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必 须 使 用 有 地 线 的 供 电 系 统 供 电 。 第 三 条 线 ( 地 线 ) 是 安 全 设 施 , 不 能 不 用 或 跳 过 。

拔掉电源 为安全地从设备拔掉电源,请拔掉所有设备后

或桌面电源的电源线,或任何接到市电系统的电源线。 电源线保护 妥善布线, 避免被踩踏,或重物挤压。

维护 所有维修必须由认证的维修人员进行。 设备内部 没有用户可以更换的零件。为避免出现触电危险不要自 己试图打开设备盖子维修该设备。

通风孔 有些设备机壳上有通风槽或孔,它们是用来防止

机内敏感元件过热。 不要用任何东西挡住通风孔。 锂电池 不正确的更换电池会有爆炸的危险。 必须使用

与厂家推荐的相同或相近型号的电池。 按照生产厂的 建议处理废弃电池。

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in

a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

NThis unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance with FCC emissions limits.

Image 3
Contents Interfaces IPL T S SeriesSafety Instructions English Precautions安全须知 中文 Page Table of Contents Table of Contents, cont’d IPL T S Series Interfaces OneIntroduction About this ManualIPL T S Series Products IPL T S1 Introduction, cont’d Global Configurator Click the Download GCSWxxxxx.exe button Installing Global ConfiguratorClick the Global Configurator icon System requirementsIntroduction, cont’d Two Front Panel Hardware SetupRear Panel Local Area Network LAN Connection Hardware Setup, cont’d Power ConnectionSerial Device Connection RJ-45 Connector Straight-through CableHardware Setup, cont’d Pin D connectorCaptive screw connector IPL T S6 Hardware Setup, cont’d Three Click the Add Driver Subscriptions button Software SetupCreating a Global Configurator Project File Step one download device driversClick the right arrow Subscribe button Step two create a new project Software Setup, cont’dIPL T S Series Interfaces Software Setup Step three add a device Click Edit Add DeviceClick Make this device a GlobalViewer Host if desired Click Auto Configure IP Address Step four define the location of the new device Step five save the new Global Configurator file Software Setup, cont’d Configuring a New Device Step six configure contactsClick Edit Contact Manager Click Edit Email Manager Step seven configure e-mailDriver Configuration tab opens Step eight assign device driversClick Add Driver Step nine set scheduled actions and e-mail deliveries Click Apply Action IPL T S Series Interfaces Software Setup Click Apply Email/Contacts Step ten set monitored conditions Click Apply Condition Click ConditionsStep eleven build the Global Configurator file Building and Uploading a GC FileApply Email/Contacts Step twelve upload the Global Configurator file Step thirteen change device settings if desired Click Tools Change Device SettingsSet Mail Server..., Set Gateway..., Set Subnet Mask..., etc Step fourteen launch GlobalViewer Software Setup, cont’d Launching the GlobalViewer InterfaceIPL T S Series Interfaces Software Setup USA, Canada, South America Japan Central America Extron’s WarrantyExtron USA East Setup Guide Checklist