Network Technologies DVB-ASI to IP To fix the equipment, To cable the equipment, Equipment access

Page 16

ASI-IP-GTW User's Manual

oWhere appropriate ensure that this product has an adequate level of lightning protection. Alternatively, during a lightning storm or whenever it is left unattended and unused for long periods of time, unplug it from the supply outlet and disconnect the output equipment. This prevents damage to the product due to lightning and power-line surges.

Warning: If the Video Gateway has been subject to a lightning strike or the power surge which has stopped it working, disconnect the power immediately. Do not reapply power until it has been checked for safety. If in doubt, contact Network.

2.2.2 To fix the equipment

The ASI-IP-GTW is designed for stationary use. The ASI-IP-GTW is designed for installation in standard 19" racks. When installed in a rack, ensure that the unit is surely and safely installed and that the equipment has adequate through-flow of air.

2.2.3 To cable the equipment

Ensure that power supply cables are routed in such a way that they are not likely to be walked on or pinched by items placed upon or against them.

Do not run ac power cables and signal cables in the same duct.

2.2.4 Equipment access

The ASI-IP-GTW has connectors at the rear. When installing the unit, ensure that the unit is installed to allow easy access to the rear of the unit.

2.2.5 Ventilation

Warning: Never push objects of any kind into this equipment through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on or into the product.

Please observe the following:

1.Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation such as a rack unless proper ventilation is provided or the instructions have been adhered to.

2.The fans contained in this unit are not fitted with dust/insect filter. Play particular attention to the environment in which it is to be used.

The ASI-IP-GTW should be installed to allow adequate flow of free- air. Ensure that the ventilation holes on each side of the ASI-IP-

Page 16

Image 16
Contents DVB-ASI to IP Gateway This page is intentionally left blank Important notice Rev Date SW ver CommentPage Table of Contents Options 12.1 Purpose of this Manual IntroductionWho Should Use this Manual Contact Information What Equipment is Covered by this ManualRole of the ASI-IP-GTW in a Typical System Summary of FeaturesSoftware versions Page Indicator Colour Description Guided TourUser Interface Front Panel DescriptionConstruction Hardware OptionsSoftware Options Functionality Max value DescriptionInstalling the Equipment Installing the EquipmentIntroduction Equipment access To fix the equipmentTo cable the equipment VentilationTo connect the equipment ASI portAC Power Supply PowerPower Cable and Protective Earth UK BS Protective Earth /Technical EarthUSA Nema 5-15P Connecting the Video Gateway to the AC Power Supply Optional DC Power SupplyPin placement Specification Introduction Signal ConnectionsASI ports DVB ASI input Ethernet data portDVB ASI output LEDs Ethernet management portPowering Up/Down Before Powering upPowering Up Powering DownOperating the Equipment Changing the IP address of the unitLooking at the WEB interface Overall statusMain tab Sub-tab Description SnmpStatus Device Info Product type ASI-IP-GTWNetwork MainAdvanced 1.22 SFPDevice info page, Network and SFP sub-page Time settings Shows the sub-page for time setting used for alarm reportsAlarms SnmpSnmp tab Ping Ping tabPage Shows the sub-page for user security password protection SecurityIP TX Input ConfigurationMain Input Status IP TX ParametersIP TX Status FEC Settings IP TX FECPage Vlan settings Ethernet SettingsStatic MAC setting Ping Settings Ping page of an IP transmitterOutput Configuration IP RXIP RX Parameters Output StatusIP RX Status FEC sub-page of an IP receiver Page Ethernet sub-page of an IP receiver Ping page of an IP receiver Advanced Tab Advanced TabPage Data Network Interface Status NetworkTransmitted Network streams Shows the Network page for a unit configured to IP-RX mode Received Network streamsSaving a Configuration Save/LoadLoading a Configuration Save/Load page when saving configurationOptions 1PPS/10MHz interface modulesSeparate 10MHz/1PPS module 2 1PPS interfaceOperating the 1PPS/10MHz interface module Shows the layoutLED descriptions LED description for separate 1PPS/10MHz interface moduleRIPv2 functionality Shows the layout of the RIP-2 screenPage Equipment Description IP Transmit ModeFunctional Description IP Bi-directional Mode IP Receive ModeManagement Page Alarm Severity level Description Overview of Video over IP Protocol mappingForward Error Correction FEC Data Flow Block DiagramsUDP Mode Page Preventive Maintenance Preventive Maintenance and Fault-findingMaintenance Fault finding Philosophy Fault-findingPreliminary Checks PSU LED Unlit / Power Supply Problem Alarm LED lit / Alarm condition Fans Not Working / OverheatingStep Action If the result of action is Yes Check Fan RotationAlarm Description Error source Progress Bitrate estimationTo return the unit Disposing of this EquipmentGeneral Appendix a Glossary Page Page Page Appendix B Technical Specification DVB ASI portAlarm relay and maintenance port specification Ethernet data portEthernet management port ProtocolsAC Mains Input DC Mains inputPhysical Details Safety Environmental ConditionsCompliance1 Electromagnetic Compatibility EMCCE Marking Interface to public telecommunication systemAppendix C References Appendix D Upgrade of Features Ex. http//192.168.0.100/upgradeFeature upgrade Feature upgrade dialogue Upgrade SW Appendix E Upgrading SoftwareSW load progress Mpls Appendix F Quality of service Setting Packet priorityLayer 3 Routing ASI-IP-GTW Configuration Layer 2 priority