Network Technologies DVB-ASI to IP, ASI-IP-GTW user manual Appendix C References

Page 86

ASI-IP-GTW User's Manual

9 Appendix C: References

oISO13818-1,2 and 3: MPEG-2 Video and Audio and Systems

oEN 300 468: Digital Video Broadcasting (DVB); Specification for Service Information (SI) in DVB systems

oRFC 1889 - RTP: A Transport Protocol for Real-Time Applications. o RFC 3550 - RTP: A Transport Protocol for Real-Time Applications.

oRFC 2733 - RTP: An RTP Payload Format for Generic Forward Error Correction.

oRFC 2250 - RTP: RTP Payload Format for MPEG1/MPEG2 Video

oRFC 3497 - RTP: Payload Format for Society of Motion Picture and Television Engineers (SMPTE) 292M Video

oRFC 3376 - IGMP: Internet Group Management Protocol, Version 3

oRFC 2236 - IGMP: Internet Group Management Protocol, Version 2

oRFC 0791 - IPv4: Internet Protocol

oRFC 3261 - SIP : Session Initiation Protocol

oRFC 0793 - TCP : Transmission Control Protocol

oRFC 0792 - ICMP: Internet Control Message Protocol o RFC 0768 - UDP : User Datagram Protocol

o RFC 0959 - FTP: File Transfer Protocol

o RFC 2068 - HTTP: Hypertext Transfer Protocol -- HTTP/1.1

o RFC 0764 - Telnet: Telnet Protocol specification

o RFC 1157 - SNMP: Simple Network Management Protocol (SNMP)

oRFC 2030 - SNTP: Simple Network Time Protocol (SNTP) Version 4 for IPv4, IPv6 and OSI

oRFC 3497 - RTP Payload Format for Society of Motion Picture and Television Engineers (SMPTE) 292M Video

oRFC 3550 - RTP: A Transport Protocol for Real-Time Applications

oPro MPEG Forum Code of Practice 3 version 2: Transmission of Professional MPEG-2 Transport Streams over IP Networks

oPro-MPEG Code of Practice \#4 release 1 July 2004 Transmission of High Bit Rate Studio Streams over IP Networks

Page 86

Image 86

Contents DVB-ASI to IP Gateway This page is intentionally left blank Important notice Rev Date SW ver CommentPage Table of Contents Options 12.1 Who Should Use this Manual IntroductionPurpose of this Manual Contact Information What Equipment is Covered by this ManualSoftware versions Summary of FeaturesRole of the ASI-IP-GTW in a Typical System Page User Interface Indicator Colour DescriptionGuided Tour Front Panel DescriptionConstruction Hardware OptionsSoftware Options Functionality Max value DescriptionIntroduction Installing the EquipmentInstalling the Equipment To cable the equipment Equipment accessTo fix the equipment VentilationTo connect the equipment ASI portPower Cable and Protective Earth PowerAC Power Supply USA Nema 5-15P Protective Earth /Technical EarthUK BS Pin placement Specification Optional DC Power SupplyConnecting the Video Gateway to the AC Power Supply ASI ports Signal ConnectionsIntroduction DVB ASI output Ethernet data portDVB ASI input LEDs Ethernet management portPowering Up Powering Up/DownBefore Powering up Powering DownOperating the Equipment Changing the IP address of the unitLooking at the WEB interface Overall statusMain tab Sub-tab Description SnmpStatus Device Info Product type ASI-IP-GTWNetwork MainAdvanced 1.22 SFPDevice info page, Network and SFP sub-page Time settings Shows the sub-page for time setting used for alarm reportsAlarms SnmpSnmp tab Ping Ping tabPage Shows the sub-page for user security password protection SecurityMain Input ConfigurationIP TX Input Status IP TX ParametersIP TX Status FEC Settings IP TX FECPage Static MAC setting Ethernet SettingsVlan settings Ping Settings Ping page of an IP transmitterOutput Configuration IP RXIP RX Status Output StatusIP RX Parameters FEC sub-page of an IP receiver Page Ethernet sub-page of an IP receiver Ping page of an IP receiver Advanced Tab Advanced TabPage Transmitted Network streams NetworkData Network Interface Status Shows the Network page for a unit configured to IP-RX mode Received Network streamsSaving a Configuration Save/LoadLoading a Configuration Save/Load page when saving configurationSeparate 10MHz/1PPS module Options1PPS/10MHz interface modules 2 1PPS interfaceOperating the 1PPS/10MHz interface module Shows the layoutLED descriptions LED description for separate 1PPS/10MHz interface moduleRIPv2 functionality Shows the layout of the RIP-2 screenPage Functional Description IP Transmit ModeEquipment Description Management IP Receive ModeIP Bi-directional Mode Page Alarm Severity level Description Overview of Video over IP Protocol mappingUDP Mode Data Flow Block DiagramsForward Error Correction FEC Page Maintenance Preventive Maintenance and Fault-findingPreventive Maintenance Preliminary Checks Fault-findingFault finding Philosophy PSU LED Unlit / Power Supply Problem Step Action If the result of action is Yes Check Fan Alarm LED lit / Alarm conditionFans Not Working / Overheating RotationAlarm Description Error source Progress Bitrate estimationGeneral Disposing of this EquipmentTo return the unit Appendix a Glossary Page Page Page Appendix B Technical Specification DVB ASI portEthernet management port Alarm relay and maintenance port specificationEthernet data port ProtocolsAC Mains Input DC Mains inputPhysical Details Compliance1 SafetyEnvironmental Conditions Electromagnetic Compatibility EMCCE Marking Interface to public telecommunication systemAppendix C References Appendix D Upgrade of Features Ex. http//192.168.0.100/upgradeFeature upgrade Feature upgrade dialogue Upgrade SW Appendix E Upgrading SoftwareSW load progress Layer 3 Routing Appendix F Quality of service Setting Packet priorityMpls ASI-IP-GTW Configuration Layer 2 priority