Network Technologies ASI-IP-GTW, DVB-ASI to IP user manual

Page 43

ASI-IP-GTW User's Manual

Resulting total rate: This is the resulting total IP bitrate including FEC overhead for this channel. The Status frame contains status parameters related to the FEC setting.

Column UDP port: This parameter is the UDP port used for the column FEC data. The value is always Media UDP port + 2 which is in accordance with Pro-MPEG CoP 3.

Row UDP port: This parameter is the UDP port used for the row FEC data. The value is always Media UDP port + 4 which is in accordance with Pro-MPEG CoP 3.

Data rate: This parameter shows the IP data rate for this channel excluding FEC data.

Column FEC rate: This parameter shows the IP data rate for the column FEC data of this channel.

Row FEC rate: This parameter shows the IP data rate for the row FEC data of this channel.

In order to make it possible to demonstrate the function of the FEC engine, ASI-IP-GTW provides a mode to drop IP packets on the transmitter.

Frame drop: Enter the percentage of packets to be dropped from this channel. This value is not stored in the unit and must be entered after each power on.

Frames dropped: This counter shows the number of frames discarded at the output of the unit.

Page 43

Image 43

Contents DVB-ASI to IP Gateway This page is intentionally left blank Rev Date SW ver Comment Important noticePage Table of Contents Options 12.1 Purpose of this Manual IntroductionWho Should Use this Manual What Equipment is Covered by this Manual Contact InformationRole of the ASI-IP-GTW in a Typical System Summary of FeaturesSoftware versions Page Front Panel Description Indicator Colour DescriptionGuided Tour User InterfaceHardware Options ConstructionFunctionality Max value Description Software OptionsInstalling the Equipment Installing the EquipmentIntroduction Ventilation Equipment accessTo fix the equipment To cable the equipmentASI port To connect the equipmentAC Power Supply PowerPower Cable and Protective Earth UK BS Protective Earth /Technical EarthUSA Nema 5-15P Connecting the Video Gateway to the AC Power Supply Optional DC Power SupplyPin placement Specification Introduction Signal ConnectionsASI ports DVB ASI input Ethernet data portDVB ASI output Ethernet management port LEDsPowering Down Powering Up/DownBefore Powering up Powering UpChanging the IP address of the unit Operating the EquipmentOverall status Looking at the WEB interfaceSnmp Main tab Sub-tab DescriptionStatus Product type ASI-IP-GTW Device InfoMain Network1.22 SFP AdvancedDevice info page, Network and SFP sub-page Shows the sub-page for time setting used for alarm reports Time settingsSnmp AlarmsSnmp tab Ping tab PingPage Security Shows the sub-page for user security password protectionIP TX Input ConfigurationMain IP TX Parameters Input StatusIP TX Status IP TX FEC FEC SettingsPage Vlan settings Ethernet SettingsStatic MAC setting Ping page of an IP transmitter Ping SettingsIP RX Output ConfigurationIP RX Parameters Output StatusIP RX Status FEC sub-page of an IP receiver Page Ethernet sub-page of an IP receiver Ping page of an IP receiver Advanced Tab Advanced TabPage Data Network Interface Status NetworkTransmitted Network streams Received Network streams Shows the Network page for a unit configured to IP-RX modeSave/Load Saving a ConfigurationSave/Load page when saving configuration Loading a Configuration2 1PPS interface Options1PPS/10MHz interface modules Separate 10MHz/1PPS moduleShows the layout Operating the 1PPS/10MHz interface moduleLED description for separate 1PPS/10MHz interface module LED descriptionsShows the layout of the RIP-2 screen RIPv2 functionalityPage Equipment Description IP Transmit ModeFunctional Description IP Bi-directional Mode IP Receive ModeManagement Page Alarm Severity level Description Protocol mapping Overview of Video over IPForward Error Correction FEC Data Flow Block DiagramsUDP Mode Page Preventive Maintenance Preventive Maintenance and Fault-findingMaintenance Fault finding Philosophy Fault-findingPreliminary Checks PSU LED Unlit / Power Supply Problem Rotation Alarm LED lit / Alarm conditionFans Not Working / Overheating Step Action If the result of action is Yes Check FanProgress Bitrate estimation Alarm Description Error sourceTo return the unit Disposing of this EquipmentGeneral Appendix a Glossary Page Page Page DVB ASI port Appendix B Technical SpecificationProtocols Alarm relay and maintenance port specificationEthernet data port Ethernet management portDC Mains input AC Mains InputPhysical Details Electromagnetic Compatibility EMC SafetyEnvironmental Conditions Compliance1Interface to public telecommunication system CE MarkingAppendix C References Ex. http//192.168.0.100/upgrade Appendix D Upgrade of FeaturesFeature upgrade Feature upgrade dialogue Appendix E Upgrading Software Upgrade SWSW load progress Mpls Appendix F Quality of service Setting Packet priorityLayer 3 Routing Layer 2 priority ASI-IP-GTW Configuration