Network Technologies DVB-ASI to IP Ethernet Settings, Vlan settings, Static MAC setting

Page 44

ASI-IP-GTW User's Manual

3.6.3 Ethernet Settings

Figure 18. The Ethernet page of an IP transmitter

3.6.3.1 VLAN settings

By enabling VLAN tagging, IEEE802.1Q VLAN tags will be added to the outgoing streams. In effect, the video data Ethernet port will act as an 802.1Q VLAN trunk.

Enable VLAN tagging: Check this box to enable VLAN tagging.

VLAN ID: Enter VLAN ID in this field. This value shall be between 1 and 4094.

VLAN Priority: Enter VLAN priority in this field. This value shall be between 0 and 7.

3.6.3.2 Static MAC setting

Static MAC destinations address is used to specify a fixed MAC destination address in outgoing streams. This makes it possible to transmit to a destination host over a one-way link. The static MAC address setting then replaces the normal ARP lookup.

Enable static MAC: Check this box to enable insertion of the static MAC address.

Static MAC: Enter the destination MAC address.

Page 44

Image 44

Contents DVB-ASI to IP Gateway This page is intentionally left blank Important notice Rev Date SW ver CommentPage Table of Contents Options 12.1 Who Should Use this Manual IntroductionPurpose of this Manual Contact Information What Equipment is Covered by this ManualSoftware versions Summary of FeaturesRole of the ASI-IP-GTW in a Typical System Page Indicator Colour Description Guided TourUser Interface Front Panel DescriptionConstruction Hardware OptionsSoftware Options Functionality Max value DescriptionIntroduction Installing the EquipmentInstalling the Equipment Equipment access To fix the equipmentTo cable the equipment VentilationTo connect the equipment ASI portPower Cable and Protective Earth PowerAC Power Supply USA Nema 5-15P Protective Earth /Technical EarthUK BS Pin placement Specification Optional DC Power SupplyConnecting the Video Gateway to the AC Power Supply ASI ports Signal ConnectionsIntroduction DVB ASI output Ethernet data portDVB ASI input LEDs Ethernet management portPowering Up/Down Before Powering upPowering Up Powering DownOperating the Equipment Changing the IP address of the unitLooking at the WEB interface Overall statusMain tab Sub-tab Description SnmpStatus Device Info Product type ASI-IP-GTWNetwork MainAdvanced 1.22 SFPDevice info page, Network and SFP sub-page Time settings Shows the sub-page for time setting used for alarm reportsAlarms SnmpSnmp tab Ping Ping tabPage Shows the sub-page for user security password protection SecurityMain Input ConfigurationIP TX Input Status IP TX ParametersIP TX Status FEC Settings IP TX FECPage Static MAC setting Ethernet SettingsVlan settings Ping Settings Ping page of an IP transmitterOutput Configuration IP RXIP RX Status Output StatusIP RX Parameters FEC sub-page of an IP receiver Page Ethernet sub-page of an IP receiver Ping page of an IP receiver Advanced Tab Advanced TabPage Transmitted Network streams NetworkData Network Interface Status Shows the Network page for a unit configured to IP-RX mode Received Network streamsSaving a Configuration Save/LoadLoading a Configuration Save/Load page when saving configurationOptions 1PPS/10MHz interface modulesSeparate 10MHz/1PPS module 2 1PPS interfaceOperating the 1PPS/10MHz interface module Shows the layoutLED descriptions LED description for separate 1PPS/10MHz interface moduleRIPv2 functionality Shows the layout of the RIP-2 screenPage Functional Description IP Transmit ModeEquipment Description Management IP Receive ModeIP Bi-directional Mode Page Alarm Severity level Description Overview of Video over IP Protocol mappingUDP Mode Data Flow Block DiagramsForward Error Correction FEC Page Maintenance Preventive Maintenance and Fault-findingPreventive Maintenance Preliminary Checks Fault-findingFault finding Philosophy PSU LED Unlit / Power Supply Problem Alarm LED lit / Alarm condition Fans Not Working / OverheatingStep Action If the result of action is Yes Check Fan RotationAlarm Description Error source Progress Bitrate estimationGeneral Disposing of this EquipmentTo return the unit Appendix a Glossary Page Page Page Appendix B Technical Specification DVB ASI portAlarm relay and maintenance port specification Ethernet data portEthernet management port ProtocolsAC Mains Input DC Mains inputPhysical Details Safety Environmental ConditionsCompliance1 Electromagnetic Compatibility EMCCE Marking Interface to public telecommunication systemAppendix C References Appendix D Upgrade of Features Ex. http//192.168.0.100/upgradeFeature upgrade Feature upgrade dialogue Upgrade SW Appendix E Upgrading SoftwareSW load progress Layer 3 Routing Appendix F Quality of service Setting Packet priorityMpls ASI-IP-GTW Configuration Layer 2 priority