Network Technologies DVB-ASI to IP user manual Device Info, Product type ASI-IP-GTW

Page 29

ASI-IP-GTW User's Manual

3.5 Device Info

Figure 8 shows the Device Info page.

Figure 8. The device info page

The upper part of the Device Info page contains product information. This includes the following parameters:

Name: The name of the unit configured by the user.

Product type: ASI-IP-GTW

Serial number: A number which uniquely identifies the unit.

Software version: The version number of the software running on the unit.

Software build time: The time and date when the software was compiled.

Internal temperature: The internal temperature of the unit shown in degrees Celsius and Fahrenheit.

Flash Power LED: When this button is pressed, the power LEDs on rear and front of unit will flash for a short period. This functionality can be used to identify a unit in a rack.

Mode of Operation: Select ‘ASI --> IP’ for IP transmit mode. In this mode the ASI connectors operate as inputs, and the MPEG2 transport streams on these can be transmitted on the Ethernet port.

Select ‘ASI <-- IP’ for IP receive mode. In this mode, the ASI connectors operate as outputs, and transport streams can be mapped from the Ethernet port to the ASI outputs.

Page 29

Image 29

Contents DVB-ASI to IP Gateway This page is intentionally left blank Rev Date SW ver Comment Important noticePage Table of Contents Options 12.1 Who Should Use this Manual IntroductionPurpose of this Manual What Equipment is Covered by this Manual Contact InformationSoftware versions Summary of FeaturesRole of the ASI-IP-GTW in a Typical System Page Guided Tour Indicator Colour DescriptionUser Interface Front Panel DescriptionHardware Options ConstructionFunctionality Max value Description Software OptionsIntroduction Installing the EquipmentInstalling the Equipment To fix the equipment Equipment accessTo cable the equipment VentilationASI port To connect the equipmentPower Cable and Protective Earth PowerAC Power Supply USA Nema 5-15P Protective Earth /Technical EarthUK BS Pin placement Specification Optional DC Power SupplyConnecting the Video Gateway to the AC Power Supply ASI ports Signal ConnectionsIntroduction DVB ASI output Ethernet data portDVB ASI input Ethernet management port LEDsBefore Powering up Powering Up/DownPowering Up Powering DownChanging the IP address of the unit Operating the EquipmentOverall status Looking at the WEB interfaceSnmp Main tab Sub-tab DescriptionStatus Product type ASI-IP-GTW Device InfoMain Network1.22 SFP AdvancedDevice info page, Network and SFP sub-page Shows the sub-page for time setting used for alarm reports Time settingsSnmp AlarmsSnmp tab Ping tab PingPage Security Shows the sub-page for user security password protectionMain Input ConfigurationIP TX IP TX Parameters Input StatusIP TX Status IP TX FEC FEC SettingsPage Static MAC setting Ethernet SettingsVlan settings Ping page of an IP transmitter Ping SettingsIP RX Output ConfigurationIP RX Status Output StatusIP RX Parameters FEC sub-page of an IP receiver Page Ethernet sub-page of an IP receiver Ping page of an IP receiver Advanced Tab Advanced TabPage Transmitted Network streams NetworkData Network Interface Status Received Network streams Shows the Network page for a unit configured to IP-RX modeSave/Load Saving a ConfigurationSave/Load page when saving configuration Loading a Configuration1PPS/10MHz interface modules OptionsSeparate 10MHz/1PPS module 2 1PPS interfaceShows the layout Operating the 1PPS/10MHz interface moduleLED description for separate 1PPS/10MHz interface module LED descriptionsShows the layout of the RIP-2 screen RIPv2 functionalityPage Functional Description IP Transmit ModeEquipment Description Management IP Receive ModeIP Bi-directional Mode Page Alarm Severity level Description Protocol mapping Overview of Video over IPUDP Mode Data Flow Block DiagramsForward Error Correction FEC Page Maintenance Preventive Maintenance and Fault-findingPreventive Maintenance Preliminary Checks Fault-findingFault finding Philosophy PSU LED Unlit / Power Supply Problem Fans Not Working / Overheating Alarm LED lit / Alarm conditionStep Action If the result of action is Yes Check Fan RotationProgress Bitrate estimation Alarm Description Error sourceGeneral Disposing of this EquipmentTo return the unit Appendix a Glossary Page Page Page DVB ASI port Appendix B Technical SpecificationEthernet data port Alarm relay and maintenance port specificationEthernet management port ProtocolsDC Mains input AC Mains InputPhysical Details Environmental Conditions SafetyCompliance1 Electromagnetic Compatibility EMCInterface to public telecommunication system CE MarkingAppendix C References Ex. http//192.168.0.100/upgrade Appendix D Upgrade of FeaturesFeature upgrade Feature upgrade dialogue Appendix E Upgrading Software Upgrade SWSW load progress Layer 3 Routing Appendix F Quality of service Setting Packet priorityMpls Layer 2 priority ASI-IP-GTW Configuration