Network Technologies DVB-ASI to IP, ASI-IP-GTW Appendix E Upgrading Software, Upgrade SW

Page 90

ASI-IP-GTW User's Manual

11 Appendix E: Upgrading Software

SW loading can be performed from the bottom of the /upgrade page, as shown in Figure 40.

This option is available on SW versions 1.3.0 and above. To load SW on older SW versions, please refer to documentation on how to load SW by FTP.

Press the ‘Browse’ button and select the file to load to the device. The file must have the filename extension ‘.out’. Then press the ‘Upload Software’ button to start the SW loading.

Figure 40 Upgrade SW

File loading from this page uses HTTP port 80, making it useful to pass through firewalls. If you have not blocked pop-ups in your browser, a progress meter (Figure 41) is displayed during file transfer. By pressing the ‘cancel’ button the transmission can be cancelled. If you do not see the progress meter, the SW loading can still be interrupted by pressing the stop button in your browser.

Page 90

Image 90

Contents DVB-ASI to IP Gateway This page is intentionally left blank Important notice Rev Date SW ver CommentPage Table of Contents Options 12.1 Introduction Purpose of this ManualWho Should Use this Manual Contact Information What Equipment is Covered by this ManualSummary of Features Role of the ASI-IP-GTW in a Typical SystemSoftware versions Page User Interface Indicator Colour DescriptionGuided Tour Front Panel DescriptionConstruction Hardware OptionsSoftware Options Functionality Max value DescriptionInstalling the Equipment Installing the EquipmentIntroduction To cable the equipment Equipment accessTo fix the equipment VentilationTo connect the equipment ASI portPower AC Power SupplyPower Cable and Protective Earth Protective Earth /Technical Earth UK BSUSA Nema 5-15P Optional DC Power Supply Connecting the Video Gateway to the AC Power SupplyPin placement Specification Signal Connections IntroductionASI ports Ethernet data port DVB ASI inputDVB ASI output LEDs Ethernet management portPowering Up Powering Up/DownBefore Powering up Powering DownOperating the Equipment Changing the IP address of the unitLooking at the WEB interface Overall statusMain tab Sub-tab Description SnmpStatus Device Info Product type ASI-IP-GTWNetwork MainAdvanced 1.22 SFPDevice info page, Network and SFP sub-page Time settings Shows the sub-page for time setting used for alarm reportsAlarms SnmpSnmp tab Ping Ping tabPage Shows the sub-page for user security password protection SecurityInput Configuration IP TXMain Input Status IP TX ParametersIP TX Status FEC Settings IP TX FECPage Ethernet Settings Vlan settingsStatic MAC setting Ping Settings Ping page of an IP transmitterOutput Configuration IP RXOutput Status IP RX ParametersIP RX Status FEC sub-page of an IP receiver Page Ethernet sub-page of an IP receiver Ping page of an IP receiver Advanced Tab Advanced TabPage Network Data Network Interface StatusTransmitted Network streams Shows the Network page for a unit configured to IP-RX mode Received Network streamsSaving a Configuration Save/LoadLoading a Configuration Save/Load page when saving configurationSeparate 10MHz/1PPS module Options1PPS/10MHz interface modules 2 1PPS interfaceOperating the 1PPS/10MHz interface module Shows the layoutLED descriptions LED description for separate 1PPS/10MHz interface moduleRIPv2 functionality Shows the layout of the RIP-2 screenPage IP Transmit Mode Equipment DescriptionFunctional Description IP Receive Mode IP Bi-directional ModeManagement Page Alarm Severity level Description Overview of Video over IP Protocol mappingData Flow Block Diagrams Forward Error Correction FECUDP Mode Page Preventive Maintenance and Fault-finding Preventive MaintenanceMaintenance Fault-finding Fault finding PhilosophyPreliminary Checks PSU LED Unlit / Power Supply Problem Step Action If the result of action is Yes Check Fan Alarm LED lit / Alarm conditionFans Not Working / Overheating RotationAlarm Description Error source Progress Bitrate estimationDisposing of this Equipment To return the unitGeneral Appendix a Glossary Page Page Page Appendix B Technical Specification DVB ASI portEthernet management port Alarm relay and maintenance port specificationEthernet data port ProtocolsAC Mains Input DC Mains inputPhysical Details Compliance1 SafetyEnvironmental Conditions Electromagnetic Compatibility EMCCE Marking Interface to public telecommunication systemAppendix C References Appendix D Upgrade of Features Ex. http//192.168.0.100/upgradeFeature upgrade Feature upgrade dialogue Upgrade SW Appendix E Upgrading SoftwareSW load progress Appendix F Quality of service Setting Packet priority MplsLayer 3 Routing ASI-IP-GTW Configuration Layer 2 priority