Network Technologies DVB-ASI to IP, ASI-IP-GTW user manual

Page 62

ASI-IP-GTW User's Manual

Metric on clear: The metric number to be used in the RIP messages when there are no active alarms in the unit.

Metric on critical: The metric number to be used in the RIP messages when there are at least one critical alarm present.

Destination: The IP destination address to use for the RIP messages.

Enable manual next hop: If set, the RIPv2 messages will specify the next hop as defined in the “Next hop address” field.

Next hop address: The address to be used for the next hop.

Route tag: Corresponds to the route tag field in the outgoing RIP messages.

Update interval: Specifies the average update interval for the RIPv2 messages. Note that the ASI-IP-GTW adds some random delay to avoid sending messages too regularly.

The status parameters are:

RIP-2 message count: Shows the number of RIP-2 messages transmitted.

Current metric: Shows the current metric used in the outgoing RIP-2 messages. Will be either the “Metric on clear” or the “Metric on critical” value.

Next hop: Shows the next hop value.

Page 62

Image 62

Contents DVB-ASI to IP Gateway This page is intentionally left blank Important notice Rev Date SW ver CommentPage Table of Contents Options 12.1 Who Should Use this Manual IntroductionPurpose of this Manual Contact Information What Equipment is Covered by this ManualSoftware versions Summary of FeaturesRole of the ASI-IP-GTW in a Typical System Page User Interface Indicator Colour DescriptionGuided Tour Front Panel DescriptionConstruction Hardware OptionsSoftware Options Functionality Max value DescriptionIntroduction Installing the EquipmentInstalling the Equipment To cable the equipment Equipment accessTo fix the equipment VentilationTo connect the equipment ASI portPower Cable and Protective Earth PowerAC Power Supply USA Nema 5-15P Protective Earth /Technical EarthUK BS Pin placement Specification Optional DC Power SupplyConnecting the Video Gateway to the AC Power Supply ASI ports Signal ConnectionsIntroduction DVB ASI output Ethernet data portDVB ASI input LEDs Ethernet management portPowering Up Powering Up/DownBefore Powering up Powering DownOperating the Equipment Changing the IP address of the unitLooking at the WEB interface Overall statusMain tab Sub-tab Description SnmpStatus Device Info Product type ASI-IP-GTWNetwork MainAdvanced 1.22 SFPDevice info page, Network and SFP sub-page Time settings Shows the sub-page for time setting used for alarm reportsAlarms SnmpSnmp tab Ping Ping tabPage Shows the sub-page for user security password protection SecurityMain Input ConfigurationIP TX Input Status IP TX ParametersIP TX Status FEC Settings IP TX FECPage Static MAC setting Ethernet SettingsVlan settings Ping Settings Ping page of an IP transmitterOutput Configuration IP RXIP RX Status Output StatusIP RX Parameters FEC sub-page of an IP receiver Page Ethernet sub-page of an IP receiver Ping page of an IP receiver Advanced Tab Advanced TabPage Transmitted Network streams NetworkData Network Interface Status Shows the Network page for a unit configured to IP-RX mode Received Network streamsSaving a Configuration Save/LoadLoading a Configuration Save/Load page when saving configurationSeparate 10MHz/1PPS module Options1PPS/10MHz interface modules 2 1PPS interfaceOperating the 1PPS/10MHz interface module Shows the layoutLED descriptions LED description for separate 1PPS/10MHz interface moduleRIPv2 functionality Shows the layout of the RIP-2 screenPage Functional Description IP Transmit ModeEquipment Description Management IP Receive ModeIP Bi-directional Mode Page Alarm Severity level Description Overview of Video over IP Protocol mappingUDP Mode Data Flow Block DiagramsForward Error Correction FEC Page Maintenance Preventive Maintenance and Fault-findingPreventive Maintenance Preliminary Checks Fault-findingFault finding Philosophy PSU LED Unlit / Power Supply Problem Step Action If the result of action is Yes Check Fan Alarm LED lit / Alarm conditionFans Not Working / Overheating RotationAlarm Description Error source Progress Bitrate estimationGeneral Disposing of this EquipmentTo return the unit Appendix a Glossary Page Page Page Appendix B Technical Specification DVB ASI portEthernet management port Alarm relay and maintenance port specificationEthernet data port ProtocolsAC Mains Input DC Mains inputPhysical Details Compliance1 SafetyEnvironmental Conditions Electromagnetic Compatibility EMCCE Marking Interface to public telecommunication systemAppendix C References Appendix D Upgrade of Features Ex. http//192.168.0.100/upgradeFeature upgrade Feature upgrade dialogue Upgrade SW Appendix E Upgrading SoftwareSW load progress Layer 3 Routing Appendix F Quality of service Setting Packet priorityMpls ASI-IP-GTW Configuration Layer 2 priority