Quatech DSCLP-200, SSCLP-300, SSCLP-200, DSCLP-300 Half-Duplex/Full-Duplex/Auto-Toggle Selection

Page 6

6.1 OS/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

6.2 DOS and other operating systems . . . . . . . . . . . . . . . . . . . 35

6.2.1 QTPCI.EXE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

7 External Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.1RTS/cts Handshake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.2RCLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.3TCLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.4AUXIN/AUXOUT Loopback . . . . . . . . . . . . . . . . . . . . . . . .

7.5Half-Duplex/Full-Duplex/Auto-Toggle Selection . . . . .

7.6Termination Resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.7RS-422/485 Peripheral Connection . . . . . . . . . . . . . . . . . .

38

39

39

40

40

41

43

44

8 PCI Resource Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

9 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

10 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

vi	DSCLP/SSCLP-200/300 User's Manual

Image 6

Contents DSCLP/SSCLP-200/300 Warranty Information Iii Application of Council Directive Manufacturers NameManufacturers Address Standards to which Conformity is DeclaredRS-422 or RS-485 Signal Line Termination Hardware ConfigurationHardware Installation Address Map and Special Registers Base Address and Interrupt Level IRQHalf-Duplex/Full-Duplex/Auto-Toggle Selection Page General Information Jumpers J6-J9 Signal Connections Full-duplex/Half-duplex OperationJumpers J10-J23 define the options for this card Right Card Edge Jumpers1 CTS0SEL, CTS1SEL J10 Enable Scratchpad Register SPAD, J2 Clock Rate and Optional RegistersForce High-Speed Uart Clock X2, X4, or X8 J3, 4 Clock multiplier jumper options Hardware Installation Jumper/connector locationsChannel Address Range Dlab Bit Spad Jumper Register selected for Enabling the Special RegistersInterrupt Status Register Bit DescriptionQuatech Modem Control Register Quatech Modem Control RegisterOptions Register Bit Name DescriptionWrite Read Clock Rate Multiplier Clock Rate Uart Clock Maximum Data Multiplier FrequencyWindows Configurations Windows MillenniumWindows Windows Page Windows Windows NT Viewing Resources with Device Manager Two-Port RS-422/RS485 Serial Adapter Page DSCLP-200/300 Two-Port RS-422/485 Serial Adapter Page Page Page Page Other Operating Systems OS/2DOS and other operating systems QTPCI.EXE QTPCI.EXE Expert Mode display External Connections Jumper/Channel correspondenceRTS/CTS Handshake RclkTclk AUXIN/AUXOUT LoopbackHalf-Duplex/Full-Duplex/Auto-Toggle Selection Half/full-duplex and Auto-Toggle selection Termination Resistors RS-422/485 Line termination resistance valuesDSCLP-200/300 connector definitions RS-422/485 Peripheral ConnectionPCI Resource Map INTA#Specifications With 64-byte FIFOs optionalTroubleshooting Computer will not boot upCannot communicate with other equipment DSCLP/SSCLP-200/300