TP-Link TL-PA4010 manual Fcc Statement, CE Mark Warning, Safety Information

Page 3
FCC STATEMENT

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1)This device may not cause harmful interference.

2)This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

Safety Information

When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source.

Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us.

Avoid water and wet locations.

II

Image 3
Contents Rev 1.0.0 TL-PA4010 AV500 Nano Powerline AdapterCOPYRIGHT & TRADEMARKS Safety Information FCC STATEMENTCE Mark Warning This product can be used in the following countries EN EN EN 61000-3-22006+A12009+A22009 EN EN DECLARATION OF CONFORMITYProduct Description AV500 Nano Powerline Adapter Rd, Nanshan, Shenzhen, ChinaAppendix A Troubleshooting CONTENTSPackage Contents Chapter 4 Using the Management UtilityPackage Contents TL-PA4010 AV500 Nano Powerline Adapter Note 1.2 System Requirement Chapter 1 Introduction1.3 Important Safety Instructions 1.1 Conventions If liquid has been spilled on the product Status Chapter 2 Connecting Mechanism2.2 LED Indicator 2.1 Introduction2.3 Physical Interface InterfaceDescription 2.5 Hardware Connection - Computer 2.4 Connection Instruction2.6 Hardware Connection - Internet  Note Chapter 3 Installing Management Utility TL-PA4010 AV500 Nano Powerline Adapter TL-PA4010 AV500 Nano Powerline Adapter TL-PA4010 AV500 Nano Powerline Adapter 4.1 Status Chapter 4 Using the Management Utility4.1.1 Set Local Device’s Network Name 4.2 Network 4.2.1 Rename the Remote Device/Enter Password Password is unnecessary to enter for renaming4.2.2 Add Device 4.3 Advanced 4.4 System 4.4.1 Upgrade Firmware 4.4.3 Set All Devices’ Network Name To upgrade the devices firmware, follow these instructions4.4.2 Reset Device  Note5.1 Pair Secure with 128 bits-AES Chapter 5 Advanced Feature How to Use the Pair Buttons5.2 Set Up a Powerline AV Network with the Pair Button Create a Powerline network using the Pair button:Join an existing Powerline AV Network Leave an existing Powerline AV NetworkThe sequence of Step 1 and Step 2 can be exchanged 2. The Ethernet LED does not light up. Ans. Check the following Appendix A Troubleshooting1. The Power LED does not light up. Ans. Check the following 3. The Powerline LED does not light up