KTI Networks kgs-1601 Port Mode, Port Flow Control, Port State, Port MaxFrame, Port Statistics

Page 33

<portlist>: Port list (Default: All ports).

2. Port Mode

Syntax:

Port Mode [<portlist>] [<mode>] Description:

Set or show the speed and duplex mode for the port. <portlist>: Port list (Default: All ports).

<mode> : Port speed and duplex mode (Default: Show configured and current mode).

10hdx : 10 Mbit/s, half duplex.

10fdx : 10 Mbit/s, full duplex.

100hdx : 100 Mbit/s, half duplex.

100fdx : 100 Mbit/s, full duplex.

1000fdx: 1 Gbit/s, full duplex.

auto : Auto negotiation of speed and duplex.

3. Port Flow Control

Syntax:

Port Flow Control [<portlist>] [enabledisable] Description:

Set or show flow control mode for the port. <portlist> : Port list (default: All ports).

[enabledisable]: Enable/disable flow control (default: Show flow control mode).

4. Port State

Syntax:

Port State [<portlist>] [enable/disable] Description:

Set or show the state for the port. <portlist> : Port list (default: All ports).

[enabledisable]: Enable or disable port state (default: Show state).

5. Port MaxFrame

Syntax:

Port MaxFrame [<portlist>] [<framesize>reset] Description:

Set or show the maximum frame size in bytes (including FCS) for frames received on the port. Tagged frames are allowed to be 4 bytes longer than the maximum frame size. Use the reset option to return to the default setting.

[<portlist>] : Port list (default: All ports).

[<framesize>reset]: Maximum frame size or reset to 1518 bytes (default: Show maximum frame size).

6. Port Statistics

Syntax:

Port Statistics [<portlist>] [clear]

Description:

-33-

Image 33
Contents Port Gigabit Ethernet Switch KGS-1601 Installation Guide Page Trademarks Table of Contents Factory Default Configuration Unpacking Information Introduction to 16-port Gigabit Web Smart Switch Key FeaturesGeneral Description Front Panel Wiring for 10/100/1000Mbps CopperPort Operation LEDs DefinitionRear Panel Rear panel of the switch is shown as belowInstalling 16-Port Gigabit Web Smart Switch Desktop InstallationRack-mount Installation Switch-to-Switch Connections Installing Network CablesNetwork Application Station ConnectionsFunctional Description Factory Default value Access the SwitchWeb Management guide Console Port Out-of-band connectionAfter authentication procedure, the home page shows up HomeAggregation QoS Mirror Statistics Discovery Page Status & Setting Functions Ables timeout. Timeout value in seconds, 0System Better network performance you will have. Default is 1518. Status & Settings FunctionsPorts Maximum value isVlan Entry There are 16 entries to set upTo add new Vlan Entry To remove the Vlan entrySettings Functions Port Port Number 1~16EgressTagging 5 QoS Aggregation/ Trunking ConfigurationTOS Value Precedence Quality of Service QoS TOS ConfigurationQoS Port Egress Rate Control QoS Port Ingress Rate ControlQoS Port Broadcast Storm Statistics MirrorAuto Search DiscoveryManual Add RemoveReboot DefaultProduct Specifications Start-up and Terminal configuration Command Line InterfaceLogin/Logout Procedures Command HierarchyHelp after a specific command Example Systemconfiguration ? You can get command information by entering ? or helpHelp Utility Prompt at top levelEntering Commands Terminology Command DescriptionMAC Address format hh-hh-hh-hh-hh-hh,hhhhhhhhhhhh or Example 00-00-24-F1-02-03System Commands Port Commands Console CommandsPort Flow Control Port ModePort State Port MaxFrameMAC Table Commands Vlan Commands Aggregation/trunking Commands QoS Commands QoS Egress Rate QoS TosprecedenceQoS Ingress Rate QoS Storm ControlIP Commands Mirror CommandsPvid ExampleFactory Default Configuration