KTI Networks kgs-1601 QoS Tosprecedence, QoS Egress Rate, QoS Ingress Rate, QoS Storm Control

Page 38

trol

configuration, ingress rate control configuration and multicast storm control

[<portlist>]: Port list (default: All ports).

2. QoS Tosprecedence

Syntax:

QoS Tosprecedence [<portlist>] [<tosprecedencelist>] [lowhigh] Description:

Set or show the IP ToS precendence priority mapping. [<portlist>] : Port list (default: All ports).

[<tosprecedencelist>]: IP ToS precedence list, 0-7 (default: All prece- dence values).

[lowhigh] : Internal priority (default: Show priority).

3. QoS Egress Rate

Syntax:

QoS EgressRate [<portlist>] [enabledisable] [<rate>] Description:

Set or show the Egress rate configuration. [<portlist>] : Port list (default: All ports).

[enabledisable]: Enable/disable Egress Rate control (default: Show shaper mode).

[<rate>] : Leaky bucket rate in Kbit/s [250-1000000k] or Mbit/s[1-1000m]

(default: Show EgressRate rate).

4. QoS Ingress Rate

Syntax:

QoS IngressRate [<portlist>] [enabledisable] [<rate>] Description:

Set or show the ingress rate configuration. [<portlist>] : Port list (default: All ports).

[enabledisable]: Enable/disable ingress rate control (default: Show IngressRate mode).

[<rate>] : Leaky bucket rate in Kbit/s [250-1000000k] or Mbit/s [1-1000m]

(default: Show Ingress rate).

5. QoS Storm Control

Syntax:

QoS Storm Control [<portlist>] [enabledisable] [<rate>] Description:

Set or show the multicast storm control configuration. Multicasts and broadcasts are controlled using a multicast ingress rate control. [<portlist>] : Port list (default: All ports).

[enabledisable]: Enable/disable the multicast ingress rate control (de-

fault: Show multicast IngressRate mode).

[<rate>] : Leaky bucket rate in Kbit/s [250-1000000k] or Mbit/s [1-1000m]

(default: Show multicast Ingress rate).

-38-

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Port Gigabit Ethernet Switch KGS-1601 Installation Guide Page Trademarks Table of Contents Factory Default Configuration Unpacking Information General Description Introduction to 16-port Gigabit Web Smart SwitchKey Features Port Operation Wiring for 10/100/1000Mbps CopperFront Panel LEDs DefinitionRear panel of the switch is shown as below Rear PanelRack-mount Installation Installing 16-Port Gigabit Web Smart SwitchDesktop Installation Network Application Installing Network CablesSwitch-to-Switch Connections Station ConnectionsFunctional Description Web Management guide Access the SwitchFactory Default value Console Port Out-of-band connectionAggregation QoS Mirror Statistics Discovery After authentication procedure, the home page shows upHome Page System Status & Setting FunctionsAbles timeout. Timeout value in seconds, 0 Ports Status & Settings FunctionsBetter network performance you will have. Default is 1518. Maximum value isTo add new Vlan Entry There are 16 entries to set upVlan Entry To remove the Vlan entryEgressTagging Settings FunctionsPort Port Number 1~16 Aggregation/ Trunking Configuration 5 QoSQuality of Service QoS TOS Configuration TOS Value PrecedenceQoS Port Broadcast Storm QoS Port Egress Rate ControlQoS Port Ingress Rate Control Mirror StatisticsManual Add DiscoveryAuto Search RemoveDefault RebootProduct Specifications Login/Logout Procedures Command Line InterfaceStart-up and Terminal configuration Command HierarchyHelp Utility You can get command information by entering ? or helpHelp after a specific command Example Systemconfiguration ? Prompt at top levelEntering Commands MAC Address format hh-hh-hh-hh-hh-hh,hhhhhhhhhhhh or Command DescriptionTerminology Example 00-00-24-F1-02-03System Commands Console Commands Port CommandsPort State Port ModePort Flow Control Port MaxFrameMAC Table Commands Vlan Commands Aggregation/trunking Commands QoS Commands QoS Ingress Rate QoS TosprecedenceQoS Egress Rate QoS Storm ControlMirror Commands IP CommandsExample PvidFactory Default Configuration
Top Page Image Contents