KTI Networks kgs-1601 manual Aggregation/trunking Commands

Page 36

4. VLAN Lookup

Syntax:

VLAN Lookup <vidlist> Description:

Lookup VLAN entry and show port list. <vidlist> : VLAN ID list.

5. VLAN EgressTagging

Syntax:

VLAN EgressTagging [<portlist>] [enabledisable] Description:

Set or show the VLAN Egress Tagging mode for the port. The enabled ports will strip the VLAN tag from received frames and insert the tag in trans- mitted frames (except PVID). The disabled ports will not strip the tag from received frames or insert the tag in transmitted frames. [<portlist>]: Port list (default: All ports).

[enabledisable]: Enable/disable VLAN egress tagging (default: Show awareness).

6. VLAN PVID

Syntax:

VLAN PVID [<portlist>] [<vid>none] Description:

Set or show the port VLAN ID. Untagged frames received on the port will be classified to this VLAN ID. Frames classified to this VLAN ID will be sent untagged on the port.

[<portlist>]: Port list (default: All ports).

[<vid>none]: Port VLAN ID, 1-4094 (default: Show PVID). The none option can be used for trunk links.

7. VLAN Frame Type

Syntax:

VLAN Frame Type [<portlist>] [alltagged] Description:

Set or show the accepted frame type for the port. [<portlist>]: Port list (default: All ports).

[alltagged]: Accept all or only tagged (default: Show frame type).

7.7.6 Aggregation/trunking Commands

Commands at Aggr level:

Aggr Configuration

Aggr Add <portlist>

Aggr Delete <portlist>

Aggr Lookup <portlist>

Aggr Mode [smacdmacxor]

1. Aggregation Configuration

Syntax:

-36-

Image 36
Contents Port Gigabit Ethernet Switch KGS-1601 Installation Guide Page Trademarks Table of Contents Factory Default Configuration Unpacking Information Introduction to 16-port Gigabit Web Smart Switch Key FeaturesGeneral Description Wiring for 10/100/1000Mbps Copper Front PanelPort Operation LEDs DefinitionRear panel of the switch is shown as below Rear PanelInstalling 16-Port Gigabit Web Smart Switch Desktop InstallationRack-mount Installation Installing Network Cables Switch-to-Switch ConnectionsNetwork Application Station ConnectionsFunctional Description Access the Switch Factory Default valueWeb Management guide Console Port Out-of-band connectionAfter authentication procedure, the home page shows up HomeAggregation QoS Mirror Statistics Discovery Page Status & Setting Functions Ables timeout. Timeout value in seconds, 0System Status & Settings Functions Better network performance you will have. Default is 1518.Ports Maximum value isThere are 16 entries to set up Vlan EntryTo add new Vlan Entry To remove the Vlan entrySettings Functions Port Port Number 1~16EgressTagging Aggregation/ Trunking Configuration 5 QoSQuality of Service QoS TOS Configuration TOS Value PrecedenceQoS Port Egress Rate Control QoS Port Ingress Rate ControlQoS Port Broadcast Storm Mirror StatisticsDiscovery Auto SearchManual Add RemoveDefault RebootProduct Specifications Command Line Interface Start-up and Terminal configurationLogin/Logout Procedures Command HierarchyYou can get command information by entering ? or help Help after a specific command Example Systemconfiguration ?Help Utility Prompt at top levelEntering Commands Command Description TerminologyMAC Address format hh-hh-hh-hh-hh-hh,hhhhhhhhhhhh or Example 00-00-24-F1-02-03System Commands Console Commands Port CommandsPort Mode Port Flow ControlPort State Port MaxFrameMAC Table Commands Vlan Commands Aggregation/trunking Commands QoS Commands QoS Tosprecedence QoS Egress RateQoS Ingress Rate QoS Storm ControlMirror Commands IP CommandsExample PvidFactory Default Configuration