KTI Networks kgs-1601 manual Example, Pvid

Page 40

7.8 Example

This example shows how to configure two VLANs with the following setup:

•VID 1 spans ports 2-16 and VID 2 spans ports 1-3, so port 2 and 3 are members of both VLANs and all 16 ports must be VLAN Egress Tagging enabled.

•Port 1 is the access port for VID 2, so PVID of port 1 must be set to 2.

•Port 2 is the trunk port for VID 1 and VID 2, so the PVID of port 2 must be set to none and port 2 must be set to accept tagged frames only

•Port 3 is the hybrid port for VID 1 and VID 2, where VID 1 is the untagged VLAN, so PVID must be set to 1.

•Ports 4-16 are access ports for VID 1.

The following CLI session does the above setup provided that the initial configuration is the default configuration:

>vlan

VLAN>add 1 2-16

***Warning: Existing entry overwritten VLAN>add 2 1-3

VLAN>egresstagging enable VLAN>pvid 1 2 VLAN>pvid 2 none VLAN>frame type 2 tagged VLAN>conf

VLAN Configuration:

Port

EgressTagging

PVID

FrameType

1:

enabled

2

All

2:

enabled

none

Tagged

3:

enabled

1

All

4:

enabled

1

All

5:

enabled

1

All

6:

enabled

1

All

7:

enabled

1

All

8:

enabled

1

All

9:

enabled

1

All

10:

enabled

1

All

11:

enabled

1

All

12:

enabled

1

All

13:

enabled

1

All

14:

enabled

1

All

15:

enabled

1

All

16:

enabled

1

All

Entries in permanent table:

1:2,3,4,5,6,7,8,9,10,11,12,13,14,15,16

2:1,2,3

VLAN>

-40-

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Port Gigabit Ethernet Switch KGS-1601 Installation Guide Page Trademarks Table of Contents Factory Default Configuration Unpacking Information Key Features Introduction to 16-port Gigabit Web Smart SwitchGeneral Description Wiring for 10/100/1000Mbps Copper Front PanelPort Operation LEDs DefinitionRear panel of the switch is shown as below Rear PanelDesktop Installation Installing 16-Port Gigabit Web Smart SwitchRack-mount Installation Installing Network Cables Switch-to-Switch ConnectionsNetwork Application Station ConnectionsFunctional Description Access the Switch Factory Default valueWeb Management guide Console Port Out-of-band connectionHome After authentication procedure, the home page shows upAggregation QoS Mirror Statistics Discovery Page Ables timeout. Timeout value in seconds, 0 Status & Setting FunctionsSystem Status & Settings Functions Better network performance you will have. Default is 1518.Ports Maximum value isThere are 16 entries to set up Vlan EntryTo add new Vlan Entry To remove the Vlan entryPort Port Number 1~16 Settings FunctionsEgressTagging Aggregation/ Trunking Configuration 5 QoSQuality of Service QoS TOS Configuration TOS Value PrecedenceQoS Port Ingress Rate Control QoS Port Egress Rate ControlQoS Port Broadcast Storm Mirror StatisticsDiscovery Auto SearchManual Add RemoveDefault RebootProduct Specifications Command Line Interface Start-up and Terminal configurationLogin/Logout Procedures Command HierarchyYou can get command information by entering ? or help Help after a specific command Example Systemconfiguration ?Help Utility Prompt at top levelEntering Commands Command Description TerminologyMAC Address format hh-hh-hh-hh-hh-hh,hhhhhhhhhhhh or Example 00-00-24-F1-02-03System Commands Console Commands Port CommandsPort Mode Port Flow ControlPort State Port MaxFrameMAC Table Commands Vlan Commands Aggregation/trunking Commands QoS Commands QoS Tosprecedence QoS Egress RateQoS Ingress Rate QoS Storm ControlMirror Commands IP CommandsExample PvidFactory Default Configuration
Top Page Image Contents