ClearOne comm operation manual Using the AP10, To answer a call, To make and disconnect a call

Page 19

CHAPTER 4: Operation

The AP10 has four basic functions: make a call, answer a call, disconnect a call, and mute. This chapter explains how to perform these functions with the AP10 unit and a telephone handset (optional) and with the Telco interface in AP-Ware. You can also use touch panels and custom control devices.

Using the AP10

AB C

To answer a call

Depending on how you have configured your AP10, an incoming call can ring on the telephone set connected to the AP10, the receive output, and pass a serial ring to the control device. An incoming call will also cause the front panel On LED to flash. You can answer the call in one of two ways:

•Press the On button [D] on either the front panel or from your remote control. This will route the call through the AP10 to the AP800. The green On LED will light. The red Off LED will extinguish.

– or –

•Answer the call by picking up the telephone handset and talking to your party over the telephone.

D E

Figure 4.1. AP10 front panel controls

✍	If auto-answer is enabled
✍	(DIP switch 4), the AP10
	will answer after the first

complete ring.

To make and disconnect a call

1.Call the party using your handset.

2.After the other party has answered, route the call through the AP10 by pressing the On button [D]. The On LED will light and the AP10 will take control of the call, disabling the telephone set. You can now safely hang up the handset without disconnecting your call.

If using an external controller, it is not necessary to press the On button [D]. The DIAL serial command automatically engages the AP10. See Serial Commands, page 22.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

If auto-disconnect is
✍ enabled (DIP	switch 5),
the AP10 will	disconnect

upon sensing loop drop or call- progress tones (depending on the position of DIP switch 6).

Image 19

Contents AP10 Telephone Interface Technical Services Group ~ 1-800-283-5936 USA ~ Iii Table of ContentsOperation AppendicesIntroduction FeaturesClearOne Communications EuMEA GmbH Professional Services GroupSales and Customer Service Technical SupportIntroduction ~ Controls and Connections UnpackingControls and Connections Front viewRear view AP10 rear-panel connectorsTelephone line requirements Before You InstallPower requirements Equipment placementTechnical Services Group ~ 1-800-283-5936 USA ~ Connect the unit Hardware SetupPhoenix connector Installation ~ Hardware SetupCreating a G-Link network Assigning device ID numbers Connecting powerDevice ID DIP switch settings Binary DIP Switch Address PositionTechnical Services Group ~ 1-800-283-5936 USA ~ Noise burst/auto-adapt DIP Switch SettingsReceive boost Call progression/loop Receive AGCAuto-answer Auto-disconnectRinging Receive reductionCalibration Noise burst adaptReceive level adjustment Transmit level adjustmentAuto-adapt To answer a call Using the AP10To make and disconnect a call Found Using the Telco InterfaceCustom control through DB-25 port To muteOther telco options ControllersTechnical Services Group ~ 1-800-283-5936 USA ~ Appendices Appendix a SpecificationsPin Description Remote connector pinoutAppendix B Pinouts Appendices ~ Appendix B PinoutsConventions Set connector pinoutLine connector pinout Appendix C Serial CommandsExample Command structureConvention Description Command form Device AA AP10 Serial CommandsAppendices ~ Appendix C Serial Commands Command FunctionCommand form Device Hookd Command form Device HookExample Command form Device Mute CH Explanation Command form Device LVL CHReturn values Command form Device NullCommand form Device TE Command form Device Terl Return valuesCommand form Device UID Command form Device TerleCommand form Device VER This Warranty is Void if Appendix D WarrantyAppendices ~ Appendix D Warranty Usoc Jacks This device uses RJ-11C and RJ21X terminal jacks Appendix E ComplianceFCC Part 15 Compliance FCC Part 68 ComplianceIC Compliance Safety InformationAppendices ~ Appendix E Compliance Appendix F Block Diagram Glossary Acoustic Echo Cancellation AECGlossary Index Index