ClearOne comm AP10 operation manual Index

Page 39

Index

Index

A

answer a call			15
AP-Ware 15, 16
AP10	3
connecting the unit				7
control		17
features			2
front-panel controls				3
operation			15
rear-panel connectors 4
auto-adapt		11, 13, 14
auto-answer			3, 11, 12, 15, 17, 23

auto-disconnect 11, 12, 15

C

calibration 13

call progression 11, 12, 14 control 17

D

device ID 7, 9

dial 23

digital signal processing 1

DIP switches 3, 19 settings 11

disconnect a call 15, 16 DTMF dialing 2, 17

E

ERL 17 ERLE 17 error 9

F

frequency response 19

G

G-Link In, Out	4, 8, 19
G-Link network	2, 7, 8

G-Link terminator 8

35

H

hook-flash 17, 24 hook-flash duration 11, 24

L

line connector 21 loop drop 11, 12, 14

M

make a call 15, 16 meter 17

mute 15, 17, 25

N

noise burst 11, 13, 26 null 26

P

pinouts 17, 20 power 4, 10, 19 Professional Services Group 1

R

re-null	17
receive AGC		11, 12
receive boost		11
receive LED		3, 9
receive level		14, 25
receive output 4, 8, 19
receive reduction			11, 13
registration		2
remote connector			8, 20
returns	2

S

serial command 15, 22 set connector 21 specifications 19

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 39

Contents AP10 Telephone Interface Technical Services Group ~ 1-800-283-5936 USA ~ Iii Table of ContentsOperation AppendicesIntroduction FeaturesClearOne Communications EuMEA GmbH Professional Services GroupSales and Customer Service Technical SupportIntroduction ~ Controls and Connections UnpackingControls and Connections Front viewRear view AP10 rear-panel connectorsTelephone line requirements Before You InstallPower requirements Equipment placementTechnical Services Group ~ 1-800-283-5936 USA ~ Connect the unit Hardware SetupInstallation ~ Hardware Setup Phoenix connectorCreating a G-Link network Assigning device ID numbers Connecting powerDevice ID DIP switch settings Binary DIP Switch Address PositionTechnical Services Group ~ 1-800-283-5936 USA ~ DIP Switch Settings Noise burst/auto-adaptReceive boost Call progression/loop Receive AGCAuto-answer Auto-disconnectRinging Receive reductionCalibration Noise burst adaptTransmit level adjustment Receive level adjustmentAuto-adapt Using the AP10 To answer a callTo make and disconnect a call Found Using the Telco InterfaceCustom control through DB-25 port To muteOther telco options ControllersTechnical Services Group ~ 1-800-283-5936 USA ~ Appendices Appendix a SpecificationsPin Description Remote connector pinoutAppendix B Pinouts Appendices ~ Appendix B PinoutsConventions Set connector pinoutLine connector pinout Appendix C Serial CommandsCommand structure ExampleConvention Description Command form Device AA AP10 Serial CommandsAppendices ~ Appendix C Serial Commands Command FunctionCommand form Device Hook Command form Device HookdExample Command form Device Mute CH Explanation Command form Device LVL CHReturn values Command form Device NullCommand form Device TE Command form Device Terl Return valuesCommand form Device Terle Command form Device UIDCommand form Device VER This Warranty is Void if Appendix D WarrantyAppendices ~ Appendix D Warranty Usoc Jacks This device uses RJ-11C and RJ21X terminal jacks Appendix E ComplianceFCC Part 15 Compliance FCC Part 68 ComplianceSafety Information IC ComplianceAppendices ~ Appendix E Compliance Appendix F Block Diagram Glossary Acoustic Echo Cancellation AECGlossary Index Index